ipq40xx: add support for Century WR142AC (#5670)
This commit add support for the yyets_le router. Hardware Highlights: SoC: Qualcomm IPQ4019 717 MHz RAM: 512M NT5CC256M16ER-EK Flash: 32M SPI NOR MX25L25635F WIFI1: 2.4 GHz 2T2R integrated WIFI2: 5 GHz 2T2R integrated Ethernet: Qualcomm QCA8075 (4x LAN, 1x WAN) USB: 1x 3.0 LEDS: power, wlan2g, wlan5g, usb Button: Reset Installation: Upload the firmware on the upgrade page of the stcok, and this will take a few minutes. This commit also supports the addition of a 128M nand flash version, just use the P&W R619AC's OpBoot to overwrite the original uboot. Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
This commit is contained in:
AmadeusGhost
GitHub
parent
4ccbf14700
commit
7459894377
@ -30,6 +30,7 @@ ALLWIFIBOARDS:= \
|
||||
asus_rt-acrh17 \
|
||||
avm_fritzrepeater-1200 \
|
||||
cellc_rtl30vw \
|
||||
century_wr142ac \
|
||||
dlink_dap2610 \
|
||||
engenius_eap2200 \
|
||||
engenius_emd1 \
|
||||
@ -104,6 +105,7 @@ $(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
|
||||
$(eval $(call generate-ipq-wifi-package,asus_rt-acrh17,ASUS RT-ACRH17/RT-AC82U/RT-AC42U))
|
||||
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
|
||||
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
|
||||
$(eval $(call generate-ipq-wifi-package,century_wr142ac,Century WR142AC))
|
||||
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
|
||||
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
|
||||
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
|
||||
|
||||
BIN
package/firmware/ipq-wifi/board-century_wr142ac.qca4019
Normal file
BIN
package/firmware/ipq-wifi/board-century_wr142ac.qca4019
Normal file
Binary file not shown.
@ -37,6 +37,11 @@ avm,fritzbox-7530 |\
|
||||
glinet,gl-b1300)
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
|
||||
;;
|
||||
century,wr142ac |\
|
||||
century,wr142ac-nand)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "wr142ac:green:wlan2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "wr142ac:green:wlan5g" "phy1tpt"
|
||||
;;
|
||||
engenius,eap1300)
|
||||
ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
|
||||
|
||||
@ -44,14 +44,16 @@ ipq40xx_setup_interfaces()
|
||||
;;
|
||||
asus,rt-acrh17|\
|
||||
asus,rt-ac58u|\
|
||||
p2w,r619ac-128m|\
|
||||
p2w,r619ac|\
|
||||
p2w,r619ac-128m|\
|
||||
zyxel,nbg6617)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
;;
|
||||
avm,fritzbox-4040|\
|
||||
century,wr142ac|\
|
||||
century,wr142ac-nand|\
|
||||
linksys,ea6350v3|\
|
||||
linksys,ea8300)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
|
||||
@ -51,13 +51,15 @@ case "$FIRMWARE" in
|
||||
8dev,habanero-dvk |\
|
||||
8dev,jalapeno |\
|
||||
alfa-network,ap120c-ac |\
|
||||
century,wr142ac |\
|
||||
century,wr142ac-nand |\
|
||||
cilab,meshpoint-one |\
|
||||
ezviz,cs-w3-wd1200g-eup |\
|
||||
glinet,gl-b1300 |\
|
||||
linksys,ea6350v3 |\
|
||||
mobipromo,cm520-79f |\
|
||||
p2w,r619ac-128m |\
|
||||
p2w,r619ac |\
|
||||
p2w,r619ac-128m |\
|
||||
qcom,ap-dk01.1-c1)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
;;
|
||||
@ -142,13 +144,15 @@ case "$FIRMWARE" in
|
||||
8dev,habanero-dvk |\
|
||||
8dev,jalapeno |\
|
||||
alfa-network,ap120c-ac |\
|
||||
century,wr142ac |\
|
||||
century,wr142ac-nand |\
|
||||
cilab,meshpoint-one |\
|
||||
ezviz,cs-w3-wd1200g-eup |\
|
||||
glinet,gl-b1300 |\
|
||||
linksys,ea6350v3 |\
|
||||
mobipromo,cm520-79f |\
|
||||
p2w,r619ac-128m |\
|
||||
p2w,r619ac |\
|
||||
p2w,r619ac-128m |\
|
||||
qcom,ap-dk01.1-c1)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
;;
|
||||
|
||||
@ -177,6 +177,7 @@ platform_do_upgrade() {
|
||||
avm,fritzbox-7530 |\
|
||||
avm,fritzrepeater-1200 |\
|
||||
avm,fritzrepeater-3000 |\
|
||||
century,wr142ac-nand |\
|
||||
cilab,meshpoint-one |\
|
||||
engenius,eap2200 |\
|
||||
mobipromo,cm520-79f |\
|
||||
@ -215,8 +216,8 @@ platform_do_upgrade() {
|
||||
askey_do_upgrade "$1"
|
||||
;;
|
||||
compex,wpj419|\
|
||||
p2w,r619ac-128m|\
|
||||
p2w,r619ac)
|
||||
p2w,r619ac|\
|
||||
p2w,r619ac-128m)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
linksys,ea6350v3 |\
|
||||
|
||||
@ -0,0 +1,64 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019-wr142ac.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Century WR142AC NAND";
|
||||
compatible = "century,wr142ac-nand";
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_1 rootfstype=squashfs";
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x170000>;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "oem-firmware";
|
||||
reg = <0x180000 0x1e80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x0 0x8000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -0,0 +1,81 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019-wr142ac.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Century WR142AC";
|
||||
compatible = "century,wr142ac";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x180000 0x1e80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -0,0 +1,247 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
usb3_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led_power: power {
|
||||
label = "wr142ac:green:power";
|
||||
gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "wr142ac:green:usb";
|
||||
gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&usb3_port1>, <&usb3_port2>, <&usb2_port1>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "wr142ac:green:wlan2g";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "wr142ac:green:wlan5g";
|
||||
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart2 {
|
||||
pinctrl-0 = <&serial_1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: serial0-pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_1_pins: serial1_pinmux {
|
||||
mux {
|
||||
pins = "gpio8", "gpio9";
|
||||
function = "blsp_uart1";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pinmux {
|
||||
mux {
|
||||
pins = "gpio36", "gpio40";
|
||||
function = "gpio";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "WR142AC";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "WR142AC";
|
||||
};
|
||||
@ -287,6 +287,34 @@ define Device/cellc_rtl30vw
|
||||
endef
|
||||
TARGET_DEVICES += cellc_rtl30vw
|
||||
|
||||
define Device/century_wr142ac
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Century
|
||||
DEVICE_MODEL := WR142AC
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
DEVICE_PACKAGES := ipq-wifi-century_wr142ac kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += century_wr142ac
|
||||
|
||||
define Device/century_wr142ac-nand
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Century
|
||||
DEVICE_MODEL := WR142AC
|
||||
DEVICE_VARIANT := NAND
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-century_wr142ac kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += century_wr142ac-nand
|
||||
|
||||
define Device/cilab_meshpoint-one
|
||||
$(call Device/8dev_jalapeno-common)
|
||||
DEVICE_VENDOR := Crisis Innovation Lab
|
||||
@ -588,9 +616,37 @@ define Device/openmesh_a62
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
|
||||
endef
|
||||
|
||||
TARGET_DEVICES += openmesh_a62
|
||||
|
||||
define Device/p2w_r619ac
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := P&W
|
||||
DEVICE_MODEL := R619AC
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGES += nand-factory.bin
|
||||
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
||||
endef
|
||||
TARGET_DEVICES += p2w_r619ac
|
||||
|
||||
define Device/p2w_r619ac-128m
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := P&W
|
||||
DEVICE_MODEL := R619AC
|
||||
DEVICE_VARIANT := 128M
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
||||
endef
|
||||
TARGET_DEVICES += p2w_r619ac-128m
|
||||
|
||||
define Device/qcom_ap-dk01.1-c1
|
||||
DEVICE_VENDOR := Qualcomm Atheros
|
||||
DEVICE_MODEL := AP-DK01.1
|
||||
@ -622,35 +678,6 @@ define Device/qcom_ap-dk04.1-c1
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
||||
|
||||
define Device/p2w_r619ac
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := P&W
|
||||
DEVICE_MODEL := R619AC
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGES += nand-factory.bin
|
||||
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
||||
endef
|
||||
TARGET_DEVICES += p2w_r619ac
|
||||
|
||||
define Device/p2w_r619ac-128m
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := P&W
|
||||
DEVICE_MODEL := R619AC
|
||||
DEVICE_VARIANT := 128M
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
||||
endef
|
||||
TARGET_DEVICES += p2w_r619ac-128m
|
||||
|
||||
define Device/qxwlan_e2600ac-c1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Qxwlan
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -785,11 +785,50 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -785,11 +785,53 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -21,6 +21,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4018-ea6350v3.dtb \
|
||||
+ qcom-ipq4018-eap1300.dtb \
|
||||
+ qcom-ipq4018-emd1.dtb \
|
||||
+ qcom-ipq4018-emr3500.dtb \
|
||||
+ qcom-ipq4018-ens620ext.dtb \
|
||||
+ qcom-ipq4018-ex6100v2.dtb \
|
||||
+ qcom-ipq4018-ex6150v2.dtb \
|
||||
@ -37,11 +38,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
qcom-ipq4019-ap.dk07.1-c2.dtb \
|
||||
+ qcom-ipq4019-a62.dtb \
|
||||
+ qcom-ipq4019-cm520-79f.dtb \
|
||||
+ qcom-ipq4019-ea8300.dtb \
|
||||
+ qcom-ipq4019-eap2200.dtb \
|
||||
+ qcom-ipq4019-fritzbox-7530.dtb \
|
||||
+ qcom-ipq4019-fritzrepeater-1200.dtb \
|
||||
+ qcom-ipq4019-fritzrepeater-3000.dtb \
|
||||
+ qcom-ipq4019-ea8300.dtb \
|
||||
+ qcom-ipq4019-habanero-dvk.dtb \
|
||||
+ qcom-ipq4019-map-ac2200.dtb \
|
||||
+ qcom-ipq4019-r619ac.dtb \
|
||||
@ -49,8 +50,10 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-e2600ac-c2.dtb \
|
||||
+ qcom-ipq4019-rtl30vw.dtb \
|
||||
+ qcom-ipq4019-u4019-32m.dtb \
|
||||
+ qcom-ipq4019-rt-acrh17.dtb \
|
||||
+ qcom-ipq4019-u4019-32m.dtb \
|
||||
+ qcom-ipq4019-wr142ac.dtb \
|
||||
+ qcom-ipq4019-wr142ac-nand.dtb \
|
||||
+ qcom-ipq4019-wpj419.dtb \
|
||||
+ qcom-ipq4028-wpj428.dtb \
|
||||
+ qcom-ipq4029-ap-303.dtb \
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -837,11 +837,51 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -837,11 +837,53 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -50,8 +50,10 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-e2600ac-c2.dtb \
|
||||
+ qcom-ipq4019-habanero-dvk.dtb \
|
||||
+ qcom-ipq4019-rtl30vw.dtb \
|
||||
+ qcom-ipq4019-u4019-32m.dtb \
|
||||
+ qcom-ipq4019-rt-acrh17.dtb \
|
||||
+ qcom-ipq4019-u4019-32m.dtb \
|
||||
+ qcom-ipq4019-wr142ac.dtb \
|
||||
+ qcom-ipq4019-wr142ac-nand.dtb \
|
||||
+ qcom-ipq4019-wpj419.dtb \
|
||||
+ qcom-ipq4028-wpj428.dtb \
|
||||
+ qcom-ipq4029-ap-303.dtb \
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user