Nanako/DHDAXCW-Rockchip-OpenWrt
1
0
Fork 0
Code Issues Pull Requests Actions 1 Packages Projects Releases Wiki Activity
DHDAXCW-Rockchip-OpenWrt/package/kernel/mac80211/patches/subsys/312-mac80211-minstrel_ht-add-flag-to-indicate-missing-in.patch
coolsnowwolf 88beed4c56 mac80211: netifd: Use a mask when using Usage: iw [options] command 
Options:
	--debug		enable netlink debugging
	--version	show version (3.4)
Commands:
	help [command]
		Print usage for all or a specific command, e.g.
		"help wowlan" or "help wowlan enable".

	event [-t] [-r] [-f]
		Monitor events from the kernel.
		-t - print timestamp
		-r - print relative timstamp
		-f - print full frame for auth/assoc etc.

	phy
	list
		List all wireless devices and their capabilities.

	phy <phyname> info
		Show capabilities for the specified wireless device.

	dev
		List all network interfaces for wireless hardware.

	dev <devname> info
		Show information for this interface.

	dev <devname> del
		Remove this virtual interface

	dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
	phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
		Add a new virtual interface with the given configuration.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

		The flags are only used for monitor interfaces, valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode

		The mesh_id is used only for mesh mode.

	dev <devname> ibss join <SSID> <freq in MHz> [HT20|HT40+|HT40-|NOHT] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde]
		Join the IBSS cell with the given SSID, if it doesn't exist create
		it on the given frequency. When fixed frequency is requested, don't
		join/create a cell on a different frequency. When a fixed BSSID is
		requested use that BSSID and do not adopt another cell's BSSID even
		if it has higher TSF and the same SSID. If an IBSS is created, create
		it with the specified basic-rates, multicast-rate and beacon-interval.

	dev <devname> ibss leave
		Leave the current IBSS cell.

	dev <devname> station dump
		List all stations known, e.g. the AP on managed interfaces

	dev <devname> station set <MAC address> vlan <ifindex>
		Set an AP VLAN for this station.

	dev <devname> station set <MAC address> plink_action <open|block>
		Set mesh peer link action for this station (peer).

	dev <devname> station del <MAC address>
		Remove the given station entry (use with caution!)

	dev <devname> station get <MAC address>
		Get information for a specific station.

	dev <devname> survey dump
		List all gathered channel survey data

	dev <devname> mesh leave
		Leave a mesh.

	dev <devname> mesh join <mesh ID> [mcast-rate <rate in Mbps>] [<param>=<value>]*
		Join a mesh with the given mesh ID with mcast-rate and mesh parameters.

	dev <devname> mpath dump
		List known mesh paths.

	dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
		Set an existing mesh path's next hop.

	dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
		Create a new mesh path (instead of relying on automatic discovery).

	dev <devname> mpath del <MAC address>
		Remove the mesh path to the given node.

	dev <devname> mpath get <MAC address>
		Get information on mesh path to the given node.

	dev <devname> scan [-u] [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
		Scan on the given frequencies and probe for the given SSIDs
		(or wildcard if not given) unless passive scanning is requested.
		If -u is specified print unknown data in the scan results.
		Specified (vendor) IEs must be well-formed.

	dev <devname> scan trigger [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
		Trigger a scan on the given frequencies with probing for the given
		SSIDs (or wildcard if not given) unless passive scanning is requested.

	dev <devname> scan dump [-u]
		Dump the current scan results. If -u is specified, print unknown
		data in scan results.

	reg get
		Print out the kernel's current regulatory domain information.

	reg set <ISO/IEC 3166-1 alpha2>
		Notify the kernel about the current regulatory domain.

	dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465]
		Join the network with the given SSID (and frequency, BSSID).
		With -w, wait for the connect to finish or fail.

	dev <devname> disconnect
		Disconnect from the current network.

	dev <devname> link
		Print information about the current link, if any.

	dev <devname> offchannel <freq> <duration>
		Leave operating channel and go to the given channel for a while.

	dev <devname> cqm rssi <threshold|off> [<hysteresis>]
		Set connection quality monitor RSSI threshold.

	phy <phyname> wowlan show
		Show WoWLAN status.

	phy <phyname> wowlan disable
		Disable WoWLAN.

	phy <phyname> wowlan enable [any] [disconnect] [magic-packet] [gtk-rekey-failure] [eap-identity-request] [4way-handshake] [rfkill-release] [patterns <pattern>*]
		Enable WoWLAN with the given triggers.
		Each pattern is given as a bytestring with '-' in places where any byte
		may be present, e.g. 00:11:22:-:44 will match 00:11:22:33:44 and
		00:11:22:33:ff:44 etc.

	dev <devname> roc start <freq> <time>

	phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
		Set a bitmap of allowed antennas to use for TX and RX.
		The driver may reject antenna configurations it cannot support.

	dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set distance <distance>
		Set appropriate coverage class for given link distance in meters.
		Valid values: 0 - 114750

	phy <phyname> set coverage <coverage class>
		Set coverage class (1 for every 3 usec of air propagation time).
		Valid values: 0 - 255.

	phy <phyname> set netns <pid>
		Put this wireless device into a different network namespace

	phy <phyname> set rts <rts threshold|off>
		Set rts threshold.

	phy <phyname> set frag <fragmentation threshold|off>
		Set fragmentation threshold.

	dev <devname> set channel <channel> [HT20|HT40+|HT40-]
	phy <phyname> set channel <channel> [HT20|HT40+|HT40-]
	dev <devname> set freq <freq> [HT20|HT40+|HT40-]
	phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
		Set frequency/channel the hardware is using, including HT
		configuration.

	phy <phyname> set name <new name>
		Rename this wireless device.

	dev <devname> set peer <MAC address>
		Set interface WDS peer.

	dev <devname> set noack_map <map>
		Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)

	dev <devname> set 4addr <on|off>
		Set interface 4addr (WDS) mode.

	dev <devname> set type <type>
		Set interface type/mode.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

	dev <devname> set meshid <meshid>
	dev <devname> set monitor <flag>*
		Set monitor flags. Valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode

	dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
		Set mesh parameter (run command without any to see available ones).

	dev <devname> set power_save <on|off>
		Set power save state to on or off.

	dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [mcs-<2.4|5> <MCS index>*]
		Sets up the specified rate masks.
		Not passing any arguments would clear the existing mask (if any).

	dev <devname> get mesh_param [<param>]
		Retrieve mesh parameter (run command without any to see available ones).

	dev <devname> get power_save <param>
		Retrieve power save state.

You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)

Do NOT screenscrape this tool, we don't consider its output stable.
2019-03-20 13:58:58 +08:00

123 lines
4.4 KiB
Diff
Raw Blame History

From: Felix Fietkau <nbd@nbd.name>
Date: Wed, 16 Jan 2019 22:32:12 +0100
Subject: [PATCH] mac80211: minstrel_ht: add flag to indicate
missing/inaccurate tx A-MPDU length
Some hardware (e.g. MediaTek MT7603) cannot report A-MPDU length in tx status
information. Add support for a flag to indicate that, to allow minstrel_ht
to use a fixed value in its internal calculation (which gives better results
than just defaulting to 1).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -2131,6 +2131,9 @@ struct ieee80211_txq {
* @IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP: The driver (or firmware) doesn't
* support QoS NDP for AP probing - that's most likely a driver bug.
*
+ * @IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN: Driver does not report accurate A-MPDU
+ * length in tx status information
+ *
* @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays
*/
enum ieee80211_hw_flags {
@@ -2176,6 +2179,7 @@ enum ieee80211_hw_flags {
IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA,
IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP,
IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP,
+ IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN,
/* keep last, obviously */
NUM_IEEE80211_HW_FLAGS
--- a/net/mac80211/debugfs.c
+++ b/net/mac80211/debugfs.c
@@ -214,6 +214,7 @@ static const char *hw_flag_names[] = {
FLAG(SUPPORTS_TDLS_BUFFER_STA),
FLAG(DEAUTH_NEED_MGD_TX_PREP),
FLAG(DOESNT_SUPPORT_QOS_NDP),
+ FLAG(TX_STATUS_NO_AMPDU_LEN),
#undef FLAG
};
--- a/net/mac80211/rc80211_minstrel_ht.c
+++ b/net/mac80211/rc80211_minstrel_ht.c
@@ -294,6 +294,15 @@ minstrel_get_ratestats(struct minstrel_h
return &mi->groups[index / MCS_GROUP_RATES].rates[index % MCS_GROUP_RATES];
}
+static unsigned int
+minstrel_ht_avg_ampdu_len(struct minstrel_ht_sta *mi)
+{
+ if (!mi->avg_ampdu_len)
+ return AVG_AMPDU_SIZE;
+
+ return MINSTREL_TRUNC(mi->avg_ampdu_len);
+}
+
/*
* Return current throughput based on the average A-MPDU length, taking into
* account the expected number of retransmissions and their expected length
@@ -309,7 +318,7 @@ minstrel_ht_get_tp_avg(struct minstrel_h
return 0;
if (group != MINSTREL_CCK_GROUP)
- nsecs = 1000 * mi->overhead / MINSTREL_TRUNC(mi->avg_ampdu_len);
+ nsecs = 1000 * mi->overhead / minstrel_ht_avg_ampdu_len(mi);
nsecs += minstrel_mcs_groups[group].duration[rate] <<
minstrel_mcs_groups[group].shift;
@@ -503,8 +512,12 @@ minstrel_ht_update_stats(struct minstrel
u16 tmp_cck_tp_rate[MAX_THR_RATES], index;
if (mi->ampdu_packets > 0) {
- mi->avg_ampdu_len = minstrel_ewma(mi->avg_ampdu_len,
- MINSTREL_FRAC(mi->ampdu_len, mi->ampdu_packets), EWMA_LEVEL);
+ if (!ieee80211_hw_check(mp->hw, TX_STATUS_NO_AMPDU_LEN))
+ mi->avg_ampdu_len = minstrel_ewma(mi->avg_ampdu_len,
+ MINSTREL_FRAC(mi->ampdu_len, mi->ampdu_packets),
+ EWMA_LEVEL);
+ else
+ mi->avg_ampdu_len = 0;
mi->ampdu_len = 0;
mi->ampdu_packets = 0;
}
@@ -709,7 +722,9 @@ minstrel_ht_tx_status(void *priv, struct
mi->ampdu_len += info->status.ampdu_len;
if (!mi->sample_wait && !mi->sample_tries && mi->sample_count > 0) {
- mi->sample_wait = 16 + 2 * MINSTREL_TRUNC(mi->avg_ampdu_len);
+ int avg_ampdu_len = minstrel_ht_avg_ampdu_len(mi);
+
+ mi->sample_wait = 16 + 2 * avg_ampdu_len;
mi->sample_tries = 1;
mi->sample_count--;
}
@@ -777,7 +792,7 @@ minstrel_calc_retransmit(struct minstrel
unsigned int cw = mp->cw_min;
unsigned int ctime = 0;
unsigned int t_slot = 9; /* FIXME */
- unsigned int ampdu_len = MINSTREL_TRUNC(mi->avg_ampdu_len);
+ unsigned int ampdu_len = minstrel_ht_avg_ampdu_len(mi);
unsigned int overhead = 0, overhead_rtscts = 0;
mrs = minstrel_get_ratestats(mi, index);
--- a/net/mac80211/rc80211_minstrel_ht_debugfs.c
+++ b/net/mac80211/rc80211_minstrel_ht_debugfs.c
@@ -163,9 +163,10 @@ minstrel_ht_stats_open(struct inode *ino
"lookaround %d\n",
max(0, (int) mi->total_packets - (int) mi->sample_packets),
mi->sample_packets);
- p += sprintf(p, "Average # of aggregated frames per A-MPDU: %d.%d\n",
- MINSTREL_TRUNC(mi->avg_ampdu_len),
- MINSTREL_TRUNC(mi->avg_ampdu_len * 10) % 10);
+ if (mi->avg_ampdu_len)
+ p += sprintf(p, "Average # of aggregated frames per A-MPDU: %d.%d\n",
+ MINSTREL_TRUNC(mi->avg_ampdu_len),
+ MINSTREL_TRUNC(mi->avg_ampdu_len * 10) % 10);
ms->len = p - ms->buf;
WARN_ON(ms->len + sizeof(*ms) > 32768);
Reference in New Issue View Git Blame Copy Permalink