This reverts commit 3295f6f1c254cd7e5e5285a05581bf6abbde8999.
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
Fixes: #17818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since commit f1c9afd80138 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd80138 for USW-Flex restores full 1 Gbps switching
performance on all ports.
Signed-off-by: Anders Melchiorsen <amelchio@nogoto.net>
Link: https://github.com/openwrt/openwrt/pull/17703
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix usage of non-existent 'caldata_patch_mac' function
by using the 'caldata_patch_data' function.
Fixes: #17734
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17737
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The image size has been changed to prevent failures in routers and bootloop
when flashing a large image using a stock bootloader. The LED trigger
package has been removed for 1910, which is no longer in use.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17630
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7621A
RAM: 128M DDR3, Winbond W631GG6MB-12 (DDR3-1600) or Winbond W631GG6MB-11
Flash: 128M, Macronix MX30LF1G18AC-TI (Dual Boot, Parallel-NAND)
Switch: MT7530, 5 ports 1Gbps
WiFi: MT7615DN, 2.4GHz 802.11n and 5GHz 802.11ac
USB: 2 ports USB 2.0
GPIO: 4 buttons (Wi-Fi, Reset, FN1, FN2), 4 LEDs (Power, Internet, FN, Wi-Fi), USB port power controls
LAN: RF-EEPROM + 0x04
WAN: RF-EEPROM + 0x28
2.4 GHz: RF-EEPROM + 0x04
5 GHz: 2.4GHz + 82:00:00:00:00:00
Disassembly:
There are 2 screws at the bottom. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 4 pin dots to the left of the radiator.
Pins (from LAN ports to LEDs):
3.3V (do not connect)
TX
RX
GND
Settings: 57600, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1910_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-4, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1910_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
Keenetic's bootloader supports booting a LZMA compressed kernel but seems to fail if the uncompressed data is larger than a fixed buffer therefore it is safer to use a uimage-lzma-loader. When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17381
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128 MB, ESMT M14D1G1664A (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 5 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n and MediaTek MT7613AEN 2T2R/5GHz 802.11ac
USB: 1 port USB 2.0
GPIO: 3 buttons (Wi-Fi, Reset, FN), 4 LEDs (Power, Internet, FN, Wi-Fi), USB port power controls
Disassembly:
At the bottom there are 4 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 4 pin dots to the left of the flash.
Pins (from LEDs to LAN ports):
3.3V (do not connect)
TX
RX
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1711_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-4, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1711_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17519
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A new syntax for LEDs was used, and migration of the LEDs configuration was
added. Used lower case hex characters for the addresses. Fixed a USB port
power issue.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17521
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a new port for the above device.
Currently, there is no easy installation method except
opening the device up and soldering a UART header on and
getting u-boot shell access. You boot the initramfs version
first using tftpboot, then once booted, you sysupgrade.
Shell access to root on vendor firmware:
admin:1234
To get U-Boot console, spam '4' into the serial console at boot.
with LEDs on the left, serial pinout is:
o - tx
o - rx
o - gnd
x - 3v3
server ip for tftpboot
192.168.0.225
The initramfs-kernel version boots without touching onboard flash with:
MT7628# tftpboot 0x80000000 openwrt-ramips-mt76x8-tplink_archer-mr200-v6-initramfs-kernel.bin
MT7628# bootm 0x80000000
Then when it boots off RAM, you copy
openwrt-ramips-mt76x8-tplink_archer-mr200-v6-squashfs-sysupgrade.bin
to /tmp/sysupgrade.bin of the device and run:
root@OpenWrt:/tmp# sysupgrade -n sysupgrade.bin
- [x] LEDs working
- [x] Buttons working
- [x] wlan detected
- [x] wwan detected
- [x] initramfs image working
- [x] sysupgrade working
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Link: https://github.com/openwrt/openwrt/pull/15610
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, Etron Technology EM68C16CWQG-25H
Flash: 32M, cFeon EN25QH256A (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n and MediaTek MT7613BEN 5 GHz 802.11ac
USB: 1 port USB 2.0
GPIO: 3 buttons (Wi-Fi, Reset, FN), 4 LEDs (Power, Internet, FN, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between the WAN port and the RESET button.
Pins (from WAN port to Reset button): VCC, TX, RX, NC, GRD
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1713_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1713_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17382
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we can set the mt76x8 SDXC pinmux in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:
* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite
For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After adding the correct package and pin group configurations,
the SDXC card slot can now function properly.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt76x8 SDXC pin register definition is incompatible with the
mtmips generic pinctrl driver structure. This hack allows us to
mux the SDXC IO to different pin groups in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch to using loader-kernel to accommodate
larger image sizes that are problematic for
many mt7621 uboots.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Link: https://github.com/openwrt/openwrt/pull/17389
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The former is deprecated in favor of nvmem-layout. In preparation for
eventual removal from the kernel, do so here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16097
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated in favor of nvmem-layout. In preparation for
eventual removal from the kernel, do so here.
Some of these are leftovers from nvmem-layout conversion.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16097
Signed-off-by: Robert Marko <robimarko@gmail.com>
The upstream mtk-sd driver did not perform specific timing
optimization for MT762x series SoC, hence the SDHC peripheral
of some boards cannot run at too high frequency. Reduce the
maximum clock frequency to fix the mmc read/write error.
Closes: https://github.com/openwrt/openwrt/issues/17364
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17375
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the process of upstreaming the local phy driver back in 2017, it
seems rt3050.dtsi was left out when updating the compatible string.
Add device reset as the driver needs it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17257
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
Hardware
* Mediatek MT7620A + Mediatek MT7610EN
* 64MB RAM
* 8MB NAND (Winbond 25064FVSIG )
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Signed-off-by: Die Peter Pan <diepeterpan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17114
Signed-off-by: John Crispin <john@phrozen.org>
Keenetic KN-3211 is a 2.4 Ghz band 11n (Wi-Fi 4) Wi-Fi repeater, based on MT7628AN.
Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 575 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 64 MiB
- 1x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- 3x LED, 1x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatenated into one
- The status button has been reassigned as the WPS button.
Flash instruction:
This device doesn't support sysupgrade, so the only way to flash OpenWrt image
is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-3211-squashfs-factory.bin"
to "KN-3211_recovery.bin" and place it in tftp server directory.
3. Connect PC with the ethernet port, press the reset button, power up
the router and keep button pressed until power led starts blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/17080
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for upcoming Keenetic KN-3911 support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
