This updates mac80211 to version 6.1.110-1. This code is based on Linux
6.1.110 and contains all fixes included in the upstream wireless
subsystem from that kernel version. This includes many bugfixes and also
some security fixes.
The removed patches are already integrated in upstream Linux 6.1.110.
The following patches were integrated in upstream Linux:
subsys/311-v6.2-wifi-mac80211-fix-and-simplify-unencrypted-drop-chec.patch
subsys/312-v6.3-wifi-cfg80211-move-A-MSDU-check-in-ieee80211_data_to.patch
subsys/313-v6.3-wifi-cfg80211-factor-out-bridge-tunnel-RFC1042-heade.patch
subsys/314-v6.3-wifi-mac80211-remove-mesh-forwarding-congestion-chec.patch
subsys/315-v6.3-wifi-mac80211-fix-receiving-A-MSDU-frames-on-mesh-in.patch
subsys/316-v6.3-wifi-mac80211-add-a-workaround-for-receiving-non-sta.patch
subsys/321-mac80211-fix-mesh-forwarding.patch
subsys/322-wifi-mac80211-fix-mesh-path-discovery-based-on-unica.patch
subsys/329-wifi-mac80211-fix-receiving-mesh-packets-in-forwardi.patch
subsys/339-wifi-cfg80211-fix-receving-mesh-packets-without-RFC1.patch
subsys/350-v6.3-wifi-mac80211-Allow-NSS-change-only-up-to-capability.patch
subsys/351-v6.9-wifi-mac80211-track-capability-opmode-NSS-separately.patch
Link: https://github.com/openwrt/openwrt/pull/16368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from 5d2a008670122f3f69eb3ab4f776d9fe9b6d76dd)
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from a57a3e5cc5942b309941d19143b7097a690eb014)
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from 2f846a33157e32d52c26cf06825f8eb1db13181d)
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from fe0240f27e9df2d0b8c0981741360f2f87b09536)
This log is noisy and useless, just ignore it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from 8d9893ff34242f887f40ca271a39e4c67c87b88d)
This log is noisy and useless, just ignore it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from 2fd0102cc3dfd81f4585e8599bf671157a4450b8)
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Milinda Brantini <C_A_T_T_E_R_Y@outlook.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from bfeef9b3d786b76510837014648db8d6c8106989)
r8126 is an out of tree driver provided by Realtek for RTL8126 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from 54623c6a1daeb029858aab96a58e0ee8607f738b)
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Milinda Brantini <C_A_T_T_E_R_Y@outlook.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from f063f4620c32b1cb6f43dd249c9cdfb4ee2bd12c)
r8125 is an out of tree driver provided by Realtek for RTL8125 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from ddb4070c96728394c22b4beb1070a26efd1c2d28)
r8168 is an out of tree driver provided by Realtek for RTL8168 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
((cherry picked from commit 1565eeda4e670cd02e9ba90179d53ac50aa8c6d0)
r8101 is an out of tree driver provided by Realtek for RTL8101 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit b72c4b53860ef7a65f486212c7393e2c2b57344b)
The vendor U-Boot implementaion on Telenor branded ZyXEL EX5700
devices does not store its environment on flash. It is instead
kept in a memory region. This is persistent over reboots, but
not over power cycling.
The dual partition failsafe system used by the vendor U-Boot
requires the OS to modify a variable in this memory environment.
This driver allows the ordinary uboot-envtools to access a
memory region like it was a partition on NOR flash.
The specific vendor U-Boot adds a "no-map" /reserved-memory
section and a top level /ubootenv node pointing to the memory
environment. The driver uses this device specific fact to
locate the region. The matching and probing code will likely
have to be adjusted for any other devices to be supported.
Example partial device tree:
/ {
..
ubootenv {
memory-region = <&uenv>;
compatible = "ubootenv";
};
..
reserved-memory {
..
uenv: ubootenv@7ffe8000 {
no-map;
reg = <0 0x7ffe8000 0 0x4000>;
};
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit b2e810f49588d1bbc90f657826e94b32474b482c)
Upstream removed SSB and BCMA, the drivers are now compiled against the
in kernel versions. No need to patch this for OpenWrt.
Link: https://github.com/openwrt/openwrt/pull/15983
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport 2 patches from upstream Linux to fix a Wifi throughput
problem.
Fixes: 323e249ce8ed ("mac80211: Update to version 6.1.97-1")
Link: https://github.com/openwrt/openwrt/pull/16007
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable parallel build while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit e7f6a7923356db09c29b052d0f5cb85e4ff8ef21)
Enable parallel build while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 48d19e645a8d96d408fd106e3b1b773dae48ccea)
increase size of ifmsh->mbss_changed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 20bd3502d3a841457cc06b3aa45646258fdcba9e)
Link: https://github.com/openwrt/openwrt/pull/15836
[Moved the patch to the end of the patch queue]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the deprecated license information from GPL-2.0 to GPL-2.0-only
as written in the COPYING file of the linux source tree.
Also add the 'COPYING' file to the PKG_LICENSE_FILES variable.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit 879826154fd3e5ec353117a9c00cecf5e38c4a16)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The lincense information for the packages mac80211 are missing.
This commit adds the missing information.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [backport]
(cherry picked from commit 3128157ec71c7be5c2e26a04b1f4b5080ebf870a)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add basic support for the LED driver for GCA230718.
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit 0682974aa8da4855ca373d195cb6365913fc1f8e)
Select DRIVER_11AX_SUPPORT and KERNEL_RELAY also for kmod-mt7996 to
prevent build failure if only this driver is selected during build and
end up with (most) required hostap features (IEEE 802.11be rates are not
yet supported).
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 83311b747012e0675f96af18793e92cb8320c707)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It has its own dedicated knob
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7d71c03ab188a58d74d6cdbeabb38b70ead2c74b)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the mfd-core.ko kernel module. It is selected by the
kmod-hwmon-gsc already.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8b4fd1c0dece936dc2c79f2a17d824512e7e7df3)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kxxhash_generic.ko is a soft dependency of kmod-fs-btrfs, but we did not
package it. Extract the kmod-lib-xxhash and then package
xxhash_generic.ko.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 2ebeda029490e308cc0e8f475e63280f960e74c4)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-fs-btrfs package has a soft dependency to kmod-crypto-blake2b
The CONFIG_BTRFS_FS kernel build option selects CONFIG_CRYPTO_BLAKE2B,
but we did not package it before.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f89091bba6be483e66c5ac14c477621f74aef203)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fac507606d75eec04762013582273468eea7ed92)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nf_dup_ipv4.ko and nf_dup_ipv6.ko kernel module were packaged by
kmod-ipt-tee and kmod-nft-dup-inet at the same time. Extract them into a
separate package used by both.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b0953c4fbf1bb0ad0844febe991636d05884c194)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this configuration it is not possible to run the radio using HE160 on channels 149-177.
Fixes: #14906
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
(cherry picked from commit a91b79fd04d58e711273d08e0b1246942b2eec98)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[Rename to 360-wifi-mac80211-do-not-pass-ap_vlan-vif-pointer-to-dri.patch]
(cherry picked from commit 3e738781a9712eaa81d5af0ecc8b55cbfe480c68)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PKG_MIRROR_HASH was updated to a wrong version.
Fixes: f64576f367eb ("mt76: update to Git HEAD (2024-04-03)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates mac80211 to version 6.1.97-1. This code is based on Linux
6.1.97 and contains all fixes included in the upstream wireless
subsystem from that kernel version. This includes many bugfixes and also
some security fixes.
The removed patches are already integrated in upstream Linux 6.1.97 or
in backports.
The following patches were integrated in upstream Linux:
ath11k/0013-wifi-ath11k-synchronize-ath11k_mac_he_gi_to_nl80211_.patch
ath11k/0035-wifi-ath11k-Use-platform_get_irq-to-get-the-interrup.patch
ath11k/0036-wifi-ath11k-fix-SAC-bug-on-peer-addition-with-sta-ba.patch
ath11k/0047-wifi-ath11k-fix-deinitialization-of-firmware-resourc.patch
ath11k/0053-wifi-ath11k-fix-writing-to-unintended-memory-region.patch
ath11k/0060-wifi-ath11k-Ignore-frags-from-uninitialized-peer-in-.patch
ath11k/0065-wifi-ath11k-fix-tx-status-reporting-in-encap-offload.patch
ath11k/0067-wifi-ath11k-Fix-SKB-corruption-in-REO-destination-ri.patch
ath11k/0069-wifi-ath11k-fix-registration-of-6Ghz-only-phy-withou.patch
ath11k/0080-wifi-ath11k-add-support-default-regdb-while-searchin.patch
ath11k/0085-wifi-ath11k-fix-memory-leak-in-WMI-firmware-stats.patch
ath11k/0086-wifi-ath11k-Add-missing-check-for-ioremap.patch
ath11k/0096-wifi-ath11k-fix-boot-failure-with-one-MSI-vector.patch
subsys/337-wifi-mac80211-fix-race-condition-on-enabling-fast-xm.patch
The following patches were integrated in upstream backports:
ath11k/901-wifi-ath11k-pci-fix-compilation-in-5.16-and-older.patch
build/080-resv_start_op.patch
build/110-backport_napi_build_skb.patch
The following files are missing in backports, we do not have to remove
them any more. Some were already missing before some were removed in
this update:
include/linux/cordic.h
include/linux/crc8.h
include/linux/eeprom_93cx6.h
include/linux/wl12xx.h
include/net/ieee80211.h
backport-include/linux/bcm47xx_nvram.h
include/linux/ath9k_platform.h
include/net/bluetooth/
backports ships a dummy Mediatek wed header for older kernel versions.
We backported the feature in our kernel, remove the dummy header:
backport-include/linux/soc/mediatek/mtk_wed.h
Remove header files for subsystems used form the mainline kernel:
include/trace/events/qrtr.h
include/net/rsi_91x.h
backport-include/linux/platform_data/brcmnand.h
Link: https://github.com/openwrt/openwrt/pull/15827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
