1845 Commits

Author SHA1 Message Date
Tianling Shen
f44ef85fd2
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-29 22:51:04 +08:00
Tianling Shen
20e161d513
uboot-mediatek: remove upstreamed patch
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-29 11:19:51 +08:00
Tianling Shen
2e7bff994d
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-29 11:03:06 +08:00
Furong Xu
03987d2d11 uboot-mediatek: Sync phy-mode for Xiaomi Redmi Router AX6000
Commit 572ea6807053 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.

Fixes: #13724
Fixes: 572ea6807053 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
2023-10-28 23:25:31 +02:00
Kristian Skramstad
5e33fdfc47 qualcommax: ipq807x: add support for Netgear WAX630
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
  GND RXD TXD, beginning from the external antennas. 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet

Wlan:
* 4x4 in 2.4GHz  : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)

Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A

Mounting: Wall and ceiling
```

```
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to the console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-10-28 19:49:18 +02:00
Tianling Shen
423186d7d8 mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Tianling Shen
fddd735dd5 uboot-mediatek: add support for CMCC RAX3000M
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Tianling Shen
7d8ffe941d arm-trusted-firmware-mediatek: add emmc/spim-nand ddr4 build for mt7981
They will be used on CMCC RAX3000M.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Furong Xu
3d8f36c310
uboot-mediatek: Sync phy-mode for Xiaomi Redmi Router AX6000
Commit 572ea6807053 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.

Signed-off-by: Furong Xu <xfr@outlook.com>
[applied to wr30u as well]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 22:29:57 +08:00
Jianhui Zhao
7e6d549cde
uboot-mediatek: fix determine the size of an uImage.FIT using 'imsz' or 'imszb'.
It must read the entire image for previous code of 'imsz' or 'imszb'.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
2023-10-28 22:25:47 +08:00
Tianling Shen
14e2410bbf
mediatek: add support for Bananapi BPi-R3 Mini support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: 128MB SPI-NAND, 8GB eMMC
  RAM: 2GB DDR4
  Ethernet: 2x 2.5GbE
  WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
  Interface: M.2 B-Key, M.2 M-Key, USB 2.0
  LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
  Button: Reset, Boot switch
  Power: 12V Type-C PD

eMMC Flash instructions:
1. SSH to BPi-R3 Mini, and upload all necessary firmware.
2. Write new GPT table:
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to BPi-R3 Mini, and upload all necessary firmware.
2. Erase and write new BL2:
   opkg install kmod-mtd-rw
   mtd erase BL2
   mtd write immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-snand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-snand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After ImmortalWrt has booted, erase UBI volumes:
   umount /mnt/ubi0*
   ubidetach -p /dev/mtd4
   ubiformat -y /dev/mtd4
   ubiattach -p /dev/mtd4
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-initramfs-recovery.itb
10. Perform sysupgrade.

Thank you Banana Pi for providing this board.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-27 13:12:56 +08:00
Tianling Shen
e1e14ce840
uboot-mediatek: import Airoha EN8801/8811H phy driver from SDK
Note: due to the lack of documentation and poor driver implementation,
the network is very unstable with high loss rate. It will only work
once (like tftpboot operation) then the link will be dead.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-26 18:41:01 +08:00
Tianling Shen
bae55c0ab3
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-23 20:15:37 +08:00
Nicolò Veronese
8849ccb995 uboot-mediatek: fix global pll clock override on mtk_spim
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
 a new system to calculate the SPI clocks has been added.

Unfortunately, the do_div macro overrides the global
 priv->pll_clk_rate field. This will cause to have a reduced
 clock rate on each subsequent SPI call.

Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-10-22 18:14:03 +02:00
Josua Mayer
71e2c64bef uboot-mvebu: armada 388 clearfog: support additional ddr configurations
Fixes Issue #13632.

Patches as submitted in v1 to u-boot mailinglist:
https://lists.denx.de/pipermail/u-boot/2023-October/533148.html

Signed-off-by: Josua Mayer <josua@solid-run.com>
2023-10-22 10:52:40 +02:00
Jianhui Zhao
4536fb4c5c uboot-mediatek: fix typo in bootmenu for GL-MT6000
Fixes: fe10f97 ("filogic: add support for GL.iNet GL-MT6000")

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-10-20 18:13:57 +02:00
Linus Walleij
9340babdcb
boot/apex: Restore the APEX boot loader
This is a partial revert of the deletion of the IXP4xx
target: we restore the APEX boot loader so we can use it
for the NSLU2 and related targets.

The APEX upstream is as dead as it gets so I have applied
OpenWrts old patches on top of the never released
v1.6.10 version and forked it into an OpenWrt variant
on GitHub. If the upstream comes back alive I will
happily switch over to it.

The file refers to the external GitHub, I suppose when
integrating this patch the file should be copied to OpenWrts
file repository and the file link changed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-10-20 13:26:45 +02:00
Tianling Shen
a6d19f0932
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-08 20:31:46 +08:00
Glen Lee
3aef61060e
ipq806x: add support for Extreme Networks AP3935
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/

SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
       NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
        4pin Serial Header | 3.3 | GND | RX | TX

MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env

 * Installation via either RJ45 console or on-board 4 PIN header

Install Method
--------------
1) Setup TFTP server, and place
     openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
     in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
     your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
     (use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
     set bootcmd 'ping 192.168.1.1; run boot_flash'
     saveenv
8) TFTP image to RAM:
     tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
     In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
     image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin

Signed-off-by: Glen Lee <g2lee@yahoo.com>
2023-10-05 00:56:57 +02:00
Tianling Shen
962067df7c
uboot-rockchip: Update to 2023.10
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-03 19:21:13 +08:00
Tianling Shen
fd651c5c13
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-29 12:53:47 +08:00
Jianhui Zhao
fe10f97439 filogic: add support for GL.iNet GL-MT6000
Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-09-29 00:18:26 +01:00
Chukun Pan
eb273ef640 uboot-mediatek: sync spi-nand driver with SDK
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".

Sync SPI-NAND driver for mediatek to fixes this:
 * Add support for Winbond W25N01KV 1Gbit chip.
 * Add support for Etron SPI-NAND chip.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-29 00:07:50 +01:00
Tianling Shen
17aaf08d98
uboot-mediatek: refresh patches
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-28 10:59:21 +08:00
Tianling Shen
975bdc7f8c
mediatek: drop useless vqmmc-supply for cmcc rax3000m
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-27 22:24:11 +08:00
Tianling Shen
dedd21c323
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-26 12:37:35 +08:00
Tianling Shen
38e87621e8
mediatek: add ubootenv support for cmcc rax3000m emmc/nand version
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-26 12:36:42 +08:00
Hauke Mehrtens
d2b5f4b2cd treewide: Add extra CPE identifier
This adds some Common Platform Enumerations (CPE) identifiers which I
found.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-09-25 23:06:33 +02:00
Tianling Shen
c351fa1d0a
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-25 10:19:11 +08:00
Elbert Mai
75ee5546e9 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-09-24 17:16:16 +02:00
Sebastian Pflieger
03123a3ae5 arm-trusted-firmware-sunxi: update to version 2.9
- detect die revision used in variants of the Allwinner H616 SoC (H313, T507)
- support for H6 boards without PMIC

Tested on Pine64+ and Orange PI Zero2

Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
2023-09-24 17:12:24 +02:00
Kristian Skramstad
76e419288f ipq807x: add support for Netgear WAX620
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
  Use the header closest to LED 4 and 5.
  They are marked with a white stroke.
  TX RX GND, beginning from "4". 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)

Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)

Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```

```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-09-24 13:09:16 +02:00
Tianling Shen
bff130e276
uboot-mediatek: rename default bootfile to immortalwrt
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-24 16:08:04 +08:00
Tianling Shen
ea666783db
mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-23 22:43:45 +08:00
Tianling Shen
697e78b83f
uboot-mediatek: add support for CMCC RAX3000M
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-23 22:43:45 +08:00
Tianling Shen
d17eb36578
arm-trusted-firmware-mediatek: add emmc/spim-nand ddr4 build for mt7981
They will be used on CMCC RAX3000M.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-23 22:43:44 +08:00
Tianling Shen
df11060923
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-23 11:46:05 +08:00
Daniel Golle
8428bed15d uboot-mediatek: add build for mt7981 rfb
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
Daniel Golle
be6e257fe6 arm-trusted-firmware-mediatek: fix copy&paste error in Makefile
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.

Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
Tianling Shen
e0ab5b6aa8
rockchip: remove Hinlink support
Just ask the vendor for firmware.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-20 11:07:49 +08:00
Tianling Shen
c7cf30e208
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-20 10:41:08 +08:00
Robert Marko
2bb418299d
uboot-mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.

In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Tianling Shen
57403533b9
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-19 10:04:49 +08:00
Zoltan HERPAI
6bf8193b25 sunxi: add support for Bananapi P2 Zero
CPU:     Allwinner H2+ quad-core Cortex-A7 @ 1.2GHz
Memory:  512Mb DDR3
Storage: SDcard, 8GB eMMC
Network: 10/100M ethernet, optional PoE support, Ampak AP6212 wifi + BT
USB:     1x USB 2.0 OTG
Other:   40-pin expansion header, mini-HDMI

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 18:15:21 +02:00
Zoltan HERPAI
12584395dc sunxi: add support for H616 SoC and Orangepi Zero 2
Specifications:

SoC:     Allwinner H616 @ 1.5 Ghz
DRAM:    1Gb LPDDR3
Power:   5V USB-C
Video:   HDMI (Type 2.0A - micro)
Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi
Storage: microSD / 2Mb SPI flash
USB:     1 USB2.0 Host
Debug    Serial UART

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 00:08:19 +02:00
Tianling Shen
10602e722d
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-12 18:36:26 +08:00
Piotr Dymacz
69f12c2f23 uboot-envtools: ramips: add support for ALFA Network AX1800RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-09-11 11:46:52 +02:00
Tianling Shen
7613856e97
Merge Official Source
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-11 09:50:09 +08:00
Daniel Golle
948ad2ec7a arm-trusted-firmware-mediatek: fix hang on reboot on MT7622
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-10 23:47:38 +01:00
Daniel Golle
9725524235 uboot-mediatek: sync mtk-snand driver with SDK
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
 * Platform data for MT7981 was actually missing and is now added.
 * Add support for Winbond W25N01KV 1Gbit chip.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-10 23:46:06 +01:00