immortalwrt/target/linux/bmips/dts/bcm63168-actiontec-t1200h.dts
Kyle Hendry f31675b69b bmips: add support for Actiontec T1200H
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)

Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.

- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
  r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
  scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
  flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
  nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
  previous firmware if vendor image is loaded

Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 65b8a978deac05894d1fd20dfe63494f4b43848d)
2025-04-02 19:11:49 +02:00

254 lines
3.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later
#include "bcm63268.dtsi"
/ {
model = "Actiontec T1200H";
compatible = "actiontec,t1200h", "brcm,bcm63168", "brcm,bcm63268";
aliases {
led-boot = &led_power_green;
led-failsafe = &led_power_red;
led-running = &led_power_green;
led-upgrade = &led_power_green;
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
wps {
label = "wps";
gpios = <&gpio 33 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "red:internet";
color = <LED_COLOR_ID_RED>;
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
};
led-1 {
label = "green:internet";
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
led-9 {
function = LED_FUNCTION_USB;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
};
led_power_green: led-20 {
function = LED_FUNCTION_POWER;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
led-22 {
function = LED_FUNCTION_WAN;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
};
led_power_red: led-35 {
function = LED_FUNCTION_POWER;
color = <LED_COLOR_ID_RED>;
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
panic-indicator;
};
led-39 {
function = LED_FUNCTION_WLAN;
color = <LED_COLOR_ID_RED>;
gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
};
led-43 {
function = LED_FUNCTION_WPS;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
};
led-44 {
function = LED_FUNCTION_WPS;
color = <LED_COLOR_ID_RED>;
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
led-46 {
label = "green:dsl";
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
led-49 {
label = "red:dsl";
color = <LED_COLOR_ID_RED>;
gpios = <&gpio 49 GPIO_ACTIVE_LOW>;
};
};
};
&ehci {
status = "okay";
};
&ethernet {
status = "okay";
nvmem-cells = <&macaddr_cferom_6a0>;
nvmem-cell-names = "mac-address";
};
&mdio_ext {
switch@1e {
compatible = "brcm,bcm53125";
reg = <0x1e>;
dsa,member = <1 0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan4";
};
port@1 {
reg = <1>;
label = "lan3";
};
port@2 {
reg = <2>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan1";
};
port@8 {
reg = <0x8>;
phy-mode = "rgmii";
ethernet = <&switch0port6>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};
&nflash {
status = "okay";
nandcs@0 {
compatible = "brcm,nandcs";
reg = <0>;
nand-ecc-step-size = <512>;
nand-ecc-strength = <15>;
nand-on-flash-bbt;
brcm,nand-oob-sector-size = <64>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "cferom";
reg = <0x0 0x20000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
macaddr_cferom_6a0: macaddr@6a0 {
reg = <0x6a0 0x6>;
};
};
};
partition@20000 {
compatible = "brcm,wfi-split";
label = "wfi";
reg = <0x20000 0x7ac0000>;
};
partition@7b00000 {
label = "data";
reg = <0x7b00000 0x400000>;
read-only;
};
};
};
};
&ohci {
status = "okay";
};
&pcie {
status = "okay";
};
&switch0 {
dsa,member = <0 0>;
ports {
port@3 {
reg = <3>;
label = "wan";
phy-handle = <&phy4>;
};
switch0port6: port@6 {
reg = <6>;
label = "extsw";
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
&uart0 {
status = "okay";
};
&usbh {
status = "okay";
};