Nanako/immortalwrt
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
immortalwrt/package/boot/uboot-mediatek/patches/451-add-bpi-r3-mini.patch
Tianling Shen 14e2410bbf
mediatek: add support for Bananapi BPi-R3 Mini support 
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: 128MB SPI-NAND, 8GB eMMC
  RAM: 2GB DDR4
  Ethernet: 2x 2.5GbE
  WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
  Interface: M.2 B-Key, M.2 M-Key, USB 2.0
  LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
  Button: Reset, Boot switch
  Power: 12V Type-C PD

eMMC Flash instructions:
1. SSH to BPi-R3 Mini, and upload all necessary firmware.
2. Write new GPT table:
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to BPi-R3 Mini, and upload all necessary firmware.
2. Erase and write new BL2:
   opkg install kmod-mtd-rw
   mtd erase BL2
   mtd write immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-snand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-snand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After ImmortalWrt has booted, erase UBI volumes:
   umount /mnt/ubi0*
   ubidetach -p /dev/mtd4
   ubiformat -y /dev/mtd4
   ubiattach -p /dev/mtd4
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-initramfs-recovery.itb
10. Perform sysupgrade.

Thank you Banana Pi for providing this board.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-27 13:12:56 +08:00

657 lines
21 KiB
Diff
Raw Blame History

This file contains invisible Unicode characters

This file contains invisible Unicode characters that are indistinguishable to humans but may be processed differently by a computer. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

--- /dev/null
+++ b/configs/mt7986a_bpi-r3-mini-emmc_defconfig
@@ -0,0 +1,138 @@
+CONFIG_ARM=y
+CONFIG_SYS_HAS_NONCACHED_MEMORY=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x40000
+CONFIG_ENV_OFFSET=0x400000
+CONFIG_DEFAULT_DEVICE_TREE="mt7986a-bpi-r3-mini"
+CONFIG_SYS_PROMPT="MT7986> "
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_TARGET_MT7986=y
+CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_ENV_OFFSET_REDUND=0x440000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_BOOTDELAY=30
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_MENU_SHOW=y
+CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-bpi-r3-mini.dtb"
+CONFIG_LOGLEVEL=7
+CONFIG_PRE_CONSOLE_BUFFER=y
+CONFIG_LOG=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_CPU=y
+CONFIG_CMD_LICENSE=y
+CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_ERASEENV=y
+CONFIG_CMD_ENV_FLAGS=y
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_PWM=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_TFTPSRV=y
+CONFIG_CMD_RARP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CDP=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_LINK_LOCAL=y
+CONFIG_CMD_PXE=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PSTORE=y
+CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
+CONFIG_CMD_UUID=y
+CONFIG_CMD_HASH=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_CMD_UBI=y
+CONFIG_CMD_UBI_RENAME=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_DEFAULT_ENV_FILE=y
+CONFIG_DEFAULT_ENV_FILE="bananapi_bpi-r3-mini_emmc_env"
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_USE_IPADDR=y
+CONFIG_IPADDR="192.168.1.1"
+CONFIG_USE_SERVERIP=y
+CONFIG_SERVERIP="192.168.1.254"
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_MTK_AHCI=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_LED=y
+CONFIG_LED_BLINK=y
+CONFIG_LED_GPIO=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_MTK=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_PHY_AIROHA=y
+CONFIG_PHY_AIROHA_EN8811H=y
+CONFIG_PHY_ETHERNET_ID=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_MDIO=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PCIE_MEDIATEK=y
+CONFIG_PHY=y
+CONFIG_PHY_MTK_TPHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7622=y
+CONFIG_PINCTRL_MT7986=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_MTK=y
+CONFIG_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MTK_SPIM=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_MTK=y
+CONFIG_USB_STORAGE=y
+CONFIG_ZSTD=y
+CONFIG_HEXDUMP=y
+CONFIG_LMB_MAX_REGIONS=64
--- /dev/null
+++ b/configs/mt7986a_bpi-r3-mini-snand_defconfig
@@ -0,0 +1,137 @@
+CONFIG_ARM=y
+CONFIG_SYS_HAS_NONCACHED_MEMORY=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="mt7986a-bpi-r3-mini"
+CONFIG_SYS_PROMPT="MT7986> "
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_TARGET_MT7986=y
+CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_BOOTDELAY=30
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_MENU_SHOW=y
+CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-bpi-r3-mini.dtb"
+CONFIG_LOGLEVEL=7
+CONFIG_PRE_CONSOLE_BUFFER=y
+CONFIG_LOG=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_CPU=y
+CONFIG_CMD_LICENSE=y
+CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_ERASEENV=y
+CONFIG_CMD_ENV_FLAGS=y
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_PWM=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_TFTPSRV=y
+CONFIG_CMD_RARP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CDP=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_LINK_LOCAL=y
+CONFIG_CMD_PXE=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_PSTORE=y
+CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
+CONFIG_CMD_UUID=y
+CONFIG_CMD_HASH=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_CMD_UBI=y
+CONFIG_CMD_UBI_RENAME=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_UBI=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_ENV_UBI_PART="ubi"
+CONFIG_ENV_UBI_VOLUME="ubootenv"
+CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_DEFAULT_ENV_FILE=y
+CONFIG_DEFAULT_ENV_FILE="bananapi_bpi-r3-mini_snand_env"
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_USE_IPADDR=y
+CONFIG_IPADDR="192.168.1.1"
+CONFIG_USE_SERVERIP=y
+CONFIG_SERVERIP="192.168.1.254"
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_MTK_AHCI=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_LED=y
+CONFIG_LED_BLINK=y
+CONFIG_LED_GPIO=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_MTK=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_PHY_AIROHA=y
+CONFIG_PHY_AIROHA_EN8811H=y
+CONFIG_PHY_ETHERNET_ID=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_MDIO=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PCIE_MEDIATEK=y
+CONFIG_PHY=y
+CONFIG_PHY_MTK_TPHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7622=y
+CONFIG_PINCTRL_MT7986=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_MTK=y
+CONFIG_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MTK_SPIM=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_MTK=y
+CONFIG_USB_STORAGE=y
+CONFIG_ZSTD=y
+CONFIG_HEXDUMP=y
+CONFIG_LMB_MAX_REGIONS=64
--- /dev/null
+++ b/arch/arm/dts/mt7986a-bpi-r3-mini.dts
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+#include "mt7986.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "Bananapi BPi-R3 Mini";
+ compatible = "mediatek,mt7986", "mediatek,mt7986-rfb";
+
+ chosen {
+ stdout-path = &uart0;
+ tick-timer = &timer0;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status_led: led-0 {
+ label = "green:status";
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "blue:wlan2g";
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "blue:wlan5g";
+ gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&eth {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>, <&en8811_pwr_a>;
+
+ mediatek,gmac-id = <0>;
+ phy-mode = "2500base-x";
+ phy-handle = <&phy14>;
+
+ phy14: eth-phy@14 {
+ compatible = "ethernet-phy-id03a2.a411";
+ reg = <14>;
+
+ airoha,rx-pol-reverse;
+
+ reset-gpios = <&gpio 49 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <20000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_default>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_1p8v>;
+ non-removable;
+ status = "okay";
+};
+
+&pinctrl {
+ en8811_pwr_a: en8811-pwr-a {
+ pins = "GPIO_11";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ output-low;
+ };
+
+ en8811_pwr_b: en8811-pwr-b {
+ pins = "GPIO_12";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ output-low;
+ };
+
+ mdio_pins: mdio-pins {
+ mux {
+ function = "eth";
+ groups = "mdc_mdio";
+ };
+ };
+
+ mmc0_pins_default: mmc0default {
+ mux {
+ function = "flash";
+ groups = "emmc_51";
+ };
+
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ conf-dsl {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ spi_flash_pins: spi0-pins-func-1 {
+ mux {
+ function = "flash";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+
+ pwm_pins: pwm0-pins-func-1 {
+ mux {
+ function = "pwm";
+ groups = "pwm0";
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins>;
+ status = "okay";
+};
+
+&spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+ must_tx;
+ enhance_timing;
+ dma_ext;
+ ipm_design;
+ support_quad;
+ tick_dly = <1>;
+ sample_sel = <0>;
+
+ spi_nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bl2";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@100000 {
+ label = "orig-env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition@80000 {
+ label = "factory";
+ reg = <0x80000 0x300000>;
+ };
+
+ partition@380000 {
+ label = "fip";
+ reg = <0x380000 0x200000>;
+ };
+
+ partition@580000 {
+ label = "ubi";
+ reg = <0x580000 0x7a80000>;
+ };
+ };
+ };
+
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "disabled";
+};
--- /dev/null
+++ b/bananapi_bpi-r3-mini_emmc_env
@@ -0,0 +1,55 @@
+ipaddr=192.168.1.1
+serverip=192.168.1.254
+loadaddr=0x46000000
+console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
+bootargs=root=/dev/mmcblk0p65
+bootcmd=if pstore check ; then run boot_recovery ; else run boot_emmc ; fi
+bootconf=config-1
+bootdelay=0
+bootfile=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-initramfs-recovery.itb
+bootfile_bl2=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-preloader.bin
+bootfile_fip=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
+bootfile_upg=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
+bootled_pwr=green:status
+bootled_rec=green:status
+bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
+bootmenu_default=0
+bootmenu_delay=0
+bootmenu_title= ( ( ( OpenWrt ) ) ) [eMMC]
+bootmenu_0=Initialize environment.=run _firstboot
+bootmenu_0d=Run default boot command.=run boot_default
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
+bootmenu_2=Boot production system from eMMC.=run boot_production ; run bootmenu_confirm_return
+bootmenu_3=Boot recovery system from eMMC.=run boot_recovery ; run bootmenu_confirm_return
+bootmenu_4=Load production system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_5=Load recovery system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to eMMC.=run boot_tftp_write_fip ; run bootmenu_confirm_return
+bootmenu_7=Load BL2 preloader via TFTP then write to eMMC.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
+bootmenu_8=Reboot.=reset
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
+boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
+boot_production=led $bootled_pwr on ; run emmc_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
+boot_recovery=led $bootled_rec on ; run emmc_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
+boot_emmc=run boot_production ; run boot_recovery
+boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run emmc_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run emmc_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run emmc_write_fip
+boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run emmc_write_bl2
+boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
+mmc_write_vol=imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc erase 0x$part_addr 0x$image_size && mmc write $loadaddr 0x$part_addr 0x$image_size
+mmc_read_vol=mmc read $loadaddr $part_addr 0x100 && imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc read $loadaddr 0x$part_addr 0x$image_size && setexpr filesize $image_size * 0x200
+part_default=production
+part_recovery=recovery
+reset_factory=eraseenv && reset
+emmc_read_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_read_vol
+emmc_read_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_read_vol
+emmc_write_bl2=mmc partconf 0 1 1 1 && mmc erase 0x0 0x400 && mmc write $fileaddr 0x0 0x400 ; mmc partconf 0 1 1 0
+emmc_write_fip=mmc erase 0x3400 0x2000 && mmc write $fileaddr 0x3400 0x2000 && mmc erase 0x2000 0x800
+emmc_write_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_write_vol
+emmc_write_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_write_vol
+_init_env=setenv _init_env ; setenv _create_env ; saveenv ; saveenv
+_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
+_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
+_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver"
--- /dev/null
+++ b/bananapi_bpi-r3-mini_snand_env
@@ -0,0 +1,57 @@
+ipaddr=192.168.1.1
+serverip=192.168.1.254
+loadaddr=0x46000000
+console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
+bootargs=root=/dev/ubiblock0_2p1
+bootconf=config-1
+bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
+bootdelay=0
+bootfile=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-initramfs-recovery.itb
+bootfile_bl2=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-snand-preloader.bin
+bootfile_fip=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
+bootfile_upg=immortalwrt-mediatek-filogic-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
+bootled_pwr=green:status
+bootled_rec=green:status
+bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
+bootmenu_default=0
+bootmenu_delay=0
+bootmenu_title= ( ( ( OpenWrt ) ) ) [SPI-NAND]
+bootmenu_0=Initialize environment.=run _firstboot
+bootmenu_0d=Run default boot command.=run boot_default
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
+bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
+bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
+bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to NAND.=run boot_tftp_write_fip ; run bootmenu_confirm_return
+bootmenu_7=Load BL2 preloader via TFTP then write to NAND.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
+bootmenu_8=Reboot.=reset
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
+boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
+boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
+boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
+boot_ubi=run boot_production ; run boot_recovery
+boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
+boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
+boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
+part_default=production
+part_recovery=recovery
+reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
+mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
+mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
+ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic 0 ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic 1
+ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
+ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
+ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
+ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
+ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
+ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic 2 && ubi write $loadaddr fit $filesize
+ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic 3 && ubi write $loadaddr recovery $filesize
+_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
+_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
+_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
+_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver"
Reference in New Issue View Git Blame Copy Permalink