6a950afde1
This adds support for the Ubiquiti Nanostation Loco M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - NS Loco M2: built-in antenna: 8 dBi; AR9287 - NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Note that only certain firmware versions accept unsigned images. Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin Tested on NanoStation Loco M2. Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit b56bcfe3be40493daecf13a4080920de2994ff54)
266 lines
7.3 KiB
Makefile
266 lines
7.3 KiB
Makefile
DEVICE_VARS += UBNT_BOARD UBNT_CHIP UBNT_TYPE UBNT_VERSION UBNT_REVISION
|
|
|
|
# On M (XW) devices the U-Boot as of version 1.1.4-s1039 doesn't like
|
|
# VERSION_DIST being on the place of major(?) version number, so we need to
|
|
# use some number.
|
|
UBNT_REVISION := $(VERSION_DIST)-$(REVISION)
|
|
|
|
# mkubntimage is using the kernel image direct
|
|
# routerboard creates partitions out of the ubnt header
|
|
define Build/mkubntimage
|
|
-$(STAGING_DIR_HOST)/bin/mkfwimage \
|
|
-B $(UBNT_BOARD) -v $(UBNT_TYPE).$(UBNT_CHIP).v6.0.0-$(VERSION_DIST)-$(REVISION) \
|
|
-k $(IMAGE_KERNEL) \
|
|
-r $@ \
|
|
-o $@
|
|
endef
|
|
|
|
# all UBNT XM/WA devices expect the kernel image to have 1024k while flash, when
|
|
# booting the image, the size doesn't matter.
|
|
define Build/mkubntimage-split
|
|
-[ -f $@ ] && ( \
|
|
dd if=$@ of=$@.old1 bs=1024k count=1; \
|
|
dd if=$@ of=$@.old2 bs=1024k skip=1; \
|
|
$(STAGING_DIR_HOST)/bin/mkfwimage \
|
|
-B $(UBNT_BOARD) -v $(UBNT_TYPE).$(UBNT_CHIP).v$(UBNT_VERSION)-$(UBNT_REVISION) \
|
|
-k $@.old1 \
|
|
-r $@.old2 \
|
|
-o $@; \
|
|
rm $@.old1 $@.old2 )
|
|
endef
|
|
|
|
# UBNT_BOARD e.g. one of (XS2, XS5, RS, XM)
|
|
# UBNT_TYPE e.g. one of (BZ, XM, XW)
|
|
# UBNT_CHIP e.g. one of (ar7240, ar933x, ar934x)
|
|
# UBNT_VERSION e.g. one of (6.0.0, 8.5.0)
|
|
define Device/ubnt
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
IMAGE_SIZE := 7552k
|
|
UBNT_BOARD := XM
|
|
UBNT_VERSION := 6.0.0
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | mkubntimage-split
|
|
endef
|
|
|
|
define Device/ubnt-xm
|
|
$(Device/ubnt)
|
|
DEVICE_PACKAGES += kmod-usb-ohci
|
|
UBNT_TYPE := XM
|
|
UBNT_CHIP := ar7240
|
|
ATH_SOC := ar7241
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
|
|
endef
|
|
|
|
define Device/ubnt-bz
|
|
$(Device/ubnt)
|
|
UBNT_TYPE := BZ
|
|
UBNT_CHIP := ar7240
|
|
ATH_SOC := ar7241
|
|
endef
|
|
|
|
define Device/ubnt-wa
|
|
$(Device/ubnt)
|
|
UBNT_TYPE := WA
|
|
UBNT_CHIP := ar934x
|
|
UBNT_BOARD := WA
|
|
UBNT_VERSION := 8.5.0
|
|
ATH_SOC := ar9342
|
|
endef
|
|
|
|
define Device/ubnt-xw
|
|
$(Device/ubnt)
|
|
UBNT_TYPE := XW
|
|
UBNT_CHIP := ar934x
|
|
UBNT_BOARD := XM
|
|
UBNT_VERSION := 6.0.4
|
|
UBNT_REVISION := 42.$(UBNT_REVISION)
|
|
ATH_SOC := ar9342
|
|
endef
|
|
|
|
define Device/ubnt_airrouter
|
|
$(Device/ubnt-xm)
|
|
DEVICE_TITLE := Ubiquiti AirRouter
|
|
SUPPORTED_DEVICES += airrouter
|
|
endef
|
|
TARGET_DEVICES += ubnt_airrouter
|
|
|
|
define Device/ubnt_bullet-m
|
|
$(Device/ubnt-xm)
|
|
DEVICE_TITLE := Ubiquiti Bullet-M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += bullet-m
|
|
endef
|
|
TARGET_DEVICES += ubnt_bullet-m
|
|
|
|
define Device/ubnt_bullet-m-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_TITLE := Ubiquiti Bullet-M (XW)
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += bullet-m-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_bullet-m-xw
|
|
|
|
define Device/ubnt_rocket-m
|
|
$(Device/ubnt-xm)
|
|
DEVICE_TITLE := Ubiquiti Rocket-M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += rocket-m
|
|
endef
|
|
TARGET_DEVICES += ubnt_rocket-m
|
|
|
|
define Device/ubnt_nanostation-loco-m
|
|
$(Device/ubnt-xm)
|
|
DEVICE_TITLE := Ubiquiti Nanostation Loco M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += bullet-m
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-loco-m
|
|
|
|
define Device/ubnt_nanostation-m
|
|
$(Device/ubnt-xm)
|
|
DEVICE_TITLE := Ubiquiti Nanostation M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += nanostation-m
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-m
|
|
|
|
define Device/ubnt_nanostation-m-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_TITLE := Ubiquiti Nanostation M (XW)
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += nanostation-m-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-m-xw
|
|
|
|
define Device/ubnt_lap-120
|
|
$(Device/ubnt-wa)
|
|
DEVICE_TITLE := Ubiquiti LiteAP ac (LAP-120)
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15744k
|
|
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
|
|
endef
|
|
TARGET_DEVICES += ubnt_lap-120
|
|
|
|
define Device/ubnt_nanobeam-ac
|
|
$(Device/ubnt-wa)
|
|
DEVICE_TITLE := Ubiquiti NanoBeam AC
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
IMAGE_SIZE := 15744k
|
|
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanobeam-ac
|
|
|
|
define Device/ubnt_nanostation-ac
|
|
$(Device/ubnt-wa)
|
|
DEVICE_TITLE := Ubiquiti Nanostation AC
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
IMAGE_SIZE := 15744k
|
|
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-ac
|
|
|
|
define Device/ubnt_nanostation-ac-loco
|
|
$(Device/ubnt-wa)
|
|
DEVICE_TITLE := Ubiquiti Nanostation AC loco
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15744k
|
|
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-ac-loco
|
|
|
|
define Device/ubnt_unifi
|
|
$(Device/ubnt-bz)
|
|
DEVICE_TITLE := Ubiquiti UniFi
|
|
SUPPORTED_DEVICES += unifi
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi
|
|
|
|
define Device/ubnt_unifiac
|
|
ATH_SOC := qca9563
|
|
IMAGE_SIZE := 7744k
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
|
|
|
|
define Device/ubnt_unifiac-lite
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_TITLE := Ubiquiti UniFi AC-Lite
|
|
SUPPORTED_DEVICES += unifiac-lite
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-lite
|
|
|
|
define Device/ubnt_unifiac-lr
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_TITLE := Ubiquiti UniFi AC-LR
|
|
SUPPORTED_DEVICES += unifiac-lite ubnt,unifiac-lite
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-lr
|
|
|
|
define Device/ubnt_unifiac-mesh
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_TITLE := Ubiquiti UniFi AC-Mesh
|
|
SUPPORTED_DEVICES += unifiac-lite
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-mesh
|
|
|
|
define Device/ubnt_unifiac-mesh-pro
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_TITLE := Ubiquiti UniFi AC-Mesh Pro
|
|
SUPPORTED_DEVICES += unifiac-pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-mesh-pro
|
|
|
|
define Device/ubnt_unifiac-pro
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_TITLE := Ubiquiti UniFi AC-Pro
|
|
DEVICE_PACKAGES += kmod-usb-core kmod-usb2
|
|
SUPPORTED_DEVICES += unifiac-pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-pro
|
|
|
|
define Device/ubnt_routerstation_common
|
|
DEVICE_PACKAGES := -kmod-ath9k -wpad-mini -uboot-envtools kmod-usb-ohci kmod-usb2 fconfig
|
|
ATH_SOC := ar7161
|
|
IMAGE_SIZE := 16128k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | mkubntimage | check-size $$$$(IMAGE_SIZE)
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
# IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
endef
|
|
|
|
define Device/ubnt_routerstation
|
|
$(Device/ubnt_routerstation_common)
|
|
DEVICE_TITLE := Ubiquiti RouterStation
|
|
UBNT_BOARD := RS
|
|
UBNT_TYPE := RSx
|
|
UBNT_CHIP := ar7100
|
|
DEVICE_PACKAGES += -swconfig
|
|
SUPPORTED_DEVICES += routerstation
|
|
endef
|
|
TARGET_DEVICES += ubnt_routerstation
|
|
|
|
define Device/ubnt_routerstation-pro
|
|
$(Device/ubnt_routerstation_common)
|
|
DEVICE_TITLE := Ubiquiti RouterStation Pro
|
|
UBNT_BOARD := RSPRO
|
|
UBNT_TYPE := RSPRO
|
|
UBNT_CHIP := ar7100pro
|
|
SUPPORTED_DEVICES += routerstation-pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_routerstation-pro
|
|
|
|
define Device/ubnt_acb-isp
|
|
$(Device/ubnt)
|
|
ATH_SOC := qca9533
|
|
IMAGE_SIZE := 15744k
|
|
DEVICE_TITLE := Ubiquiti airCube ISP
|
|
UBNT_BOARD := ACB-ISP
|
|
UBNT_TYPE := ACB
|
|
UBNT_CHIP := qca9533
|
|
IMAGES := sysupgrade.bin
|
|
endef
|
|
TARGET_DEVICES += ubnt_acb-isp
|