Merge Official Source

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>

package/base-files/files/sbin/wifi

@@ -130,10 +130,12 @@ wifi_updown() {
 		ubus_wifi_cmd "$cmd" "$2"
 		scan_wifi
 		cmd=up
+		ubus call network reload
 	}
 	[ reconf = "$1" ] && {
 		scan_wifi
 		cmd=reconf
+		ubus call network reload
 	}
 	ubus_wifi_cmd "$cmd" "$2"
 	_wifi_updown "$@"
@@ -246,7 +248,7 @@ case "$1" in
 	reload) wifi_reload "$2";;
 	reload_legacy) wifi_reload_legacy "$2";;
 	--help|help) usage;;
-	reconf) ubus call network reload; wifi_updown "reconf" "$2";;
+	reconf) wifi_updown "reconf" "$2";;
-	''|up) ubus call network reload; wifi_updown "enable" "$2";;
+	''|up) wifi_updown "enable" "$2";;
 	*) usage; exit 1;;
 esac

package/kernel/mac80211/files/lib/netifd/wireless/mac80211.sh

@@ -1021,10 +1021,8 @@ drv_mac80211_setup() {
 		return 1
 	}
 
-	[ -z "$(uci -q -P /var/state show wireless._${phy})" ] && {
+	wireless_set_data phy="$phy"
-		uci -q -P /var/state set wireless._${phy}=phy
+	[ -z "$(uci -q -P /var/state show wireless._${phy})" ] && uci -q -P /var/state set wireless._${phy}=phy
-		wireless_set_data phy="$phy"
-	}
 
 	OLDAPLIST=$(uci -q -P /var/state get wireless._${phy}.aplist)
 	OLDSPLIST=$(uci -q -P /var/state get wireless._${phy}.splist)
@@ -1117,6 +1115,7 @@ drv_mac80211_setup() {
 	[ -n "$hostapd_ctrl" ] && {
 		local no_reload=1
 		if [ -n "$(ubus list | grep hostapd.$primary_ap)" ]; then
+			no_reload=0
 			[ "${NEW_MD5}" = "${OLD_MD5}" ] || {
 				ubus call hostapd.$primary_ap reload
 				no_reload=$?
@@ -1191,6 +1190,10 @@ drv_mac80211_teardown() {
 	json_select data
 	json_get_vars phy
 	json_select ..
+	[ -n "$phy" ] || {
+		echo "Bug: PHY is undefined for device '$1'"
+		return 1
+	}
 
 	mac80211_interface_cleanup "$phy"
 	uci -q -P /var/state revert wireless._${phy}

package/kernel/mac80211/patches/subsys/379-mac80211-fix-starting-aggregation-sessions-on-mesh-i.patch

@@ -0,0 +1,112 @@
+From: Felix Fietkau <nbd@nbd.name>
+Date: Tue, 29 Jun 2021 13:25:09 +0200
+Subject: [PATCH] mac80211: fix starting aggregation sessions on mesh
+ interfaces
+
+The logic for starting aggregation sessions was recently moved from minstrel_ht
+to mac80211, into the subif tx handler just after the sta lookup.
+Unfortunately this didn't work for mesh interfaces, since the sta lookup is
+deferred until a much later point in time on those.
+Fix this by also calling the aggregation check right after the deferred sta
+lookup.
+
+Fixes: 08a46c642001 ("mac80211: move A-MPDU session check from minstrel_ht to mac80211")
+Signed-off-by: Felix Fietkau <nbd@nbd.name>
+---
+
+--- a/net/mac80211/tx.c
++++ b/net/mac80211/tx.c
+@@ -1159,6 +1159,29 @@ static bool ieee80211_tx_prep_agg(struct
+ 	return queued;
+ }
+ 
++static void
++ieee80211_aggr_check(struct ieee80211_sub_if_data *sdata,
++		     struct sta_info *sta,
++		     struct sk_buff *skb)
++{
++	struct rate_control_ref *ref = sdata->local->rate_ctrl;
++	u16 tid;
++
++	if (!ref || !(ref->ops->capa & RATE_CTRL_CAPA_AMPDU_TRIGGER))
++		return;
++
++	if (!sta || !sta->sta.ht_cap.ht_supported ||
++	    !sta->sta.wme || skb_get_queue_mapping(skb) == IEEE80211_AC_VO ||
++	    skb->protocol == sdata->control_port_protocol)
++		return;
++
++	tid = skb->priority & IEEE80211_QOS_CTL_TID_MASK;
++	if (likely(sta->ampdu_mlme.tid_tx[tid]))
++		return;
++
++	ieee80211_start_tx_ba_session(&sta->sta, tid, 0);
++}
++
+ /*
+  * initialises @tx
+  * pass %NULL for the station if unknown, a valid pointer if known
+@@ -1172,6 +1195,7 @@ ieee80211_tx_prepare(struct ieee80211_su
+ 	struct ieee80211_local *local = sdata->local;
+ 	struct ieee80211_hdr *hdr;
+ 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
++	bool aggr_check = false;
+ 	int tid;
+ 
+ 	memset(tx, 0, sizeof(*tx));
+@@ -1202,8 +1226,10 @@ ieee80211_tx_prepare(struct ieee80211_su
+ 			   tx->sdata->control_port_protocol == tx->skb->protocol) {
+ 			tx->sta = sta_info_get_bss(sdata, hdr->addr1);
+ 		}
+-		if (!tx->sta && !is_multicast_ether_addr(hdr->addr1))
++		if (!tx->sta && !is_multicast_ether_addr(hdr->addr1)) {
+ 			tx->sta = sta_info_get(sdata, hdr->addr1);
++			aggr_check = true;
++		}
+ 	}
+ 
+ 	if (tx->sta && ieee80211_is_data_qos(hdr->frame_control) &&
+@@ -1213,8 +1239,12 @@ ieee80211_tx_prepare(struct ieee80211_su
+ 		struct tid_ampdu_tx *tid_tx;
+ 
+ 		tid = ieee80211_get_tid(hdr);
+-
+ 		tid_tx = rcu_dereference(tx->sta->ampdu_mlme.tid_tx[tid]);
++		if (!tid_tx && aggr_check) {
++			ieee80211_aggr_check(sdata, tx->sta, skb);
++			tid_tx = rcu_dereference(tx->sta->ampdu_mlme.tid_tx[tid]);
++		}
++
+ 		if (tid_tx) {
+ 			bool queued;
+ 
+@@ -3949,29 +3979,6 @@ void ieee80211_txq_schedule_start(struct
+ }
+ EXPORT_SYMBOL(ieee80211_txq_schedule_start);
+ 
+-static void
+-ieee80211_aggr_check(struct ieee80211_sub_if_data *sdata,
+-		     struct sta_info *sta,
+-		     struct sk_buff *skb)
+-{
+-	struct rate_control_ref *ref = sdata->local->rate_ctrl;
+-	u16 tid;
+-
+-	if (!ref || !(ref->ops->capa & RATE_CTRL_CAPA_AMPDU_TRIGGER))
+-		return;
+-
+-	if (!sta || !sta->sta.ht_cap.ht_supported ||
+-	    !sta->sta.wme || skb_get_queue_mapping(skb) == IEEE80211_AC_VO ||
+-	    skb->protocol == sdata->control_port_protocol)
+-		return;
+-
+-	tid = skb->priority & IEEE80211_QOS_CTL_TID_MASK;
+-	if (likely(sta->ampdu_mlme.tid_tx[tid]))
+-		return;
+-
+-	ieee80211_start_tx_ba_session(&sta->sta, tid, 0);
+-}
+-
+ void __ieee80211_subif_start_xmit(struct sk_buff *skb,
+ 				  struct net_device *dev,
+ 				  u32 info_flags,

package/network/services/dnsmasq/files/dnsmasq.init

@@ -161,7 +161,7 @@ append_server() {
 }
 
 append_rev_server() {
-        xappend "--rev-server=$1"
+	xappend "--rev-server=$1"
 }
 
 append_address() {
@@ -878,8 +878,16 @@ dnsmasq_start()
 	append_bool "$cfg" noresolv "--no-resolv"
 	append_bool "$cfg" localise_queries "--localise-queries"
 	append_bool "$cfg" readethers "--read-ethers"
-	append_bool "$cfg" dbus "--enable-dbus"
+
-	append_bool "$cfg" ubus "--enable-ubus"	1
+	local instance_name="dnsmasq.$cfg"
+	if [ "$cfg" = "$DEFAULT_INSTANCE" ]; then
+		instance_name="dnsmasq"
+	fi
+	config_get_bool dbus "$cfg" "dbus" 0
+	[ $dbus -gt 0 ] && xappend "--enable-dbus=uk.org.thekelleys.$instance_name"
+	config_get_bool ubus "$cfg" "ubus" 1
+	[ $ubus -gt 0 ] && xappend "--enable-ubus=$instance_name"
+
 	append_bool "$cfg" expandhosts "--expand-hosts"
 	config_get tftp_root "$cfg" "tftp_root"
 	[ -n "$tftp_root" ] && mkdir -p "$tftp_root" && append_bool "$cfg" enable_tftp "--enable-tftp"
@@ -1178,6 +1186,7 @@ boot()
 start_service() {
 	local instance="$1"
 	local instance_found=0
+	local first_instance=""
 
 	. /lib/functions/network.sh
 
@@ -1188,10 +1197,27 @@ start_service() {
 			if [ -n "$instance" ] && [ "$instance" = "$name" ]; then
 				instance_found=1
 			fi
+			if [ -z "$DEFAULT_INSTANCE" ]; then
+				local disabled
+				config_get_bool disabled "$name" disabled 0
+				if [ "$disabled" -eq 0 ]; then
+					# First enabled section will be assigned default instance name.
+					# Unnamed sections get precedence over named sections.
+					if expr "$cfg" : 'cfg[0-9a-f]*$' >/dev/null = "9"; then # See uci_fixup_section.
+						DEFAULT_INSTANCE="$name" # Unnamed config section.
+					elif [ -z "$first_instance" ]; then
+						first_instance="$name"
+					fi
+				fi
+			fi
 		fi
 	}
 
+	DEFAULT_INSTANCE=""
 	config_load dhcp
+	if [ -z "$DEFAULT_INSTANCE" ]; then
+		DEFAULT_INSTANCE="$first_instance" # No unnamed config section was found.
+	fi
 
 	if [ -n "$instance" ]; then
 		[ "$instance_found" -gt 0 ] || return

package/network/utils/iwinfo/Makefile

@@ -11,9 +11,9 @@ PKG_RELEASE:=1
 
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_URL=$(PROJECT_GIT)/project/iwinfo.git
-PKG_SOURCE_DATE:=2021-06-09
+PKG_SOURCE_DATE:=2021-06-28
-PKG_SOURCE_VERSION:=c0414642fead263a4a6a686ad3cb7e965ec8a23a
+PKG_SOURCE_VERSION:=c9b1672f5a83c8dcb14fdbaee651f775a7defe52
-PKG_MIRROR_HASH:=c5686bbae86753c53db03a686b034bbb80d31107cc359ebd8522ea1c82db35ea
+PKG_MIRROR_HASH:=f33779035153da6bd0b2f100f402f62f1554ab87ed6fbbd938d41df6b9947a1f
 PKG_MAINTAINER:=Jo-Philipp Wich <jo@mein.io>
 PKG_LICENSE:=GPL-2.0
 

package/system/zram-swap/files/zram.init

@@ -2,8 +2,8 @@
 
 START=15
 
-extra_command "compact" "Trigger compaction for all Z-RAM swap dev's"
+extra_command "compact" "Trigger compaction for all zram swap devices"
-extra_command "status" "Print out information & statistics about Z-RAM swap devices"
+extra_command "status" "Print out information & statistics about zram swap devices"
 
 ram_getsize()
 {
@@ -60,15 +60,15 @@ zram_comp_algo()
 	local zram_comp_algo="$( uci -q get system.@system[0].zram_comp_algo )"
 
 	if [ -z "$zram_comp_algo" ]; then
-		# lzo-rle fails on small RAM devices, default to lzo, which is always available
+		# default to lzo, which is always available
 		zram_comp_algo="lzo"
 	fi
 
 	if [ $(grep -c "$zram_comp_algo" /sys/block/$( basename $dev )/comp_algorithm) -ne 0 ]; then
-		logger -s -t zram_comp_algo -p daemon.debug "Set compression algorithm '$zram_comp_algo' for zram '$dev'"
+		logger -s -t zram_comp_algo -p daemon.debug "set compression algorithm '$zram_comp_algo' for zram '$dev'"
 		echo $zram_comp_algo > "/sys/block/$( basename $dev )/comp_algorithm"
 	else
-		logger -s -t zram_comp_algo -p daemon.debug "Compression algorithm '$zram_comp_algo' is not supported for '$dev'"
+		logger -s -t zram_comp_algo -p daemon.debug "compression algorithm '$zram_comp_algo' is not supported for '$dev'"
 	fi
 }
 
@@ -79,7 +79,7 @@ zram_stats()
 
 	printf "\nGathering stats info for zram device \"$( basename "$1" )\"\n\n"
 
-	printf "Z-RAM\n-----\n"
+	printf "ZRAM\n----\n"
 	printf "%-25s - %s\n" "Block device" $zdev
 	awk '{ printf "%-25s - %d MiB\n", "Device size", $1/1024/1024 }' <$zdev/disksize
 	printf "%-25s - %s\n" "Compression algo" "$(cat $zdev/comp_algorithm)"
@@ -131,7 +131,7 @@ start()
 	}
 
 	if [ $( grep -cs zram /proc/swaps ) -ne 0 ]; then
-		logger -s -t zram_start -p daemon.notice "[OK] zram swap is already mounted"
+		logger -s -t zram_start -p daemon.notice "zram swap is already mounted"
 		return 1
 	fi
 
@@ -144,15 +144,18 @@ start()
 
 	local zram_size="$( zram_getsize )"
 	local zram_priority="$( uci -q get system.@system[0].zram_priority )"
-	zram_priority=${zram_priority:+-p $zram_priority}
 
-	logger -s -t zram_start -p daemon.debug "activating '$zram_dev' for swapping ($zram_size MegaBytes)"
+	if [ -z "$zram_priority" ]; then
+		zram_priority="100"
+	fi
+
+	logger -s -t zram_start -p daemon.debug "activating '$zram_dev' for swapping ($zram_size MiB)"
 
 	zram_reset "$zram_dev" "enforcing defaults"
 	zram_comp_algo "$zram_dev"
 	echo $(( $zram_size * 1024 * 1024 )) >"/sys/block/$( basename "$zram_dev" )/disksize"
 	busybox mkswap "$zram_dev"
-	busybox swapon -d $zram_priority "$zram_dev"
+	busybox swapon -d -p $zram_priority "$zram_dev"
 }
 
 stop()

package/utils/busybox/files/sysntpd

@@ -56,7 +56,14 @@ start_ntpd_instance() {
 	procd_set_param command "$PROG" -n -N
 	if [ "$enable_server" = "1" ]; then
 		procd_append_param command -l
-		[ -n "$interface" ] && procd_append_param command -I $interface
+		[ -n "$interface" ] && {
+			local ifname
+
+			network_get_device ifname "$interface" || \
+				ifname="$interface"
+			procd_append_param command -I "$ifname"
+			procd_append_param netdev "$ifname"
+		}
 	fi
 	[ -x "$HOTPLUG_SCRIPT" ] && procd_append_param command -S "$HOTPLUG_SCRIPT"
 	for peer in $server; do
@@ -79,11 +86,12 @@ start_ntpd_instance() {
 }
 
 start_service() {
+	. /lib/functions/network.sh
 	validate_ntp_section ntp start_ntpd_instance
 }
 
 service_triggers() {
-	local script name use_dhcp
+	local script name use_dhcp enable_server interface
 
 	script=$(readlink -f "$initscript")
 	name=$(basename ${script:-$initscript})
@@ -106,5 +114,17 @@ service_triggers() {
 		fi
 	}
 
+	config_get_bool enable_server ntp enable_server 0
+	config_get interface ntp interface
+
+	[ $enable_server -eq 1 ] && [ -n "$interface" ] && {
+		local ifname
+
+		network_get_device ifname "$interface" || \
+			ifname="$interface"
+		procd_add_interface_trigger "interface.*" "$ifname" \
+			/etc/init.d/"$name" reload
+	}
+
 	procd_add_validation validate_ntp_section
 }

target/linux/ath79/image/mikrotik.mk

@@ -13,7 +13,7 @@ define Device/mikrotik_routerboard-912uag-2hpnd
   $(Device/mikrotik_nand)
   SOC := ar9342
   DEVICE_MODEL := RouterBOARD 912UAG-2HPnD
-  DEVICE_PACKAGES += kmod-usb-ehci kmod-usb2 kmod-gpio-beeper
+  DEVICE_PACKAGES += kmod-usb-ehci kmod-usb2
   SUPPORTED_DEVICES += rb-912uag-2hpnd
 endef
 TARGET_DEVICES += mikrotik_routerboard-912uag-2hpnd

target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh

@@ -29,6 +29,7 @@ preinit_set_mac_address() {
 		base_mac=$(cat /sys/class/net/eth0/address)
 		ip link set dev eth0 address $(macaddr_add "$base_mac" 2)
 		ip link set dev eth1 address $(macaddr_add "$base_mac" 3)
+		;;
 	esac
 }
 

target/linux/ipq806x/config-5.4

@@ -4,22 +4,6 @@ CONFIG_ALIGNMENT_TRAP=y
 CONFIG_AR8216_PHY=y
 CONFIG_ARCH_32BIT_OFF_T=y
 CONFIG_ARCH_CLOCKSOURCE_DATA=y
-CONFIG_ARCH_HAS_BINFMT_FLAT=y
-CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-CONFIG_ARCH_HAS_KCOV=y
-CONFIG_ARCH_HAS_KEEPINITRD=y
-CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y
-CONFIG_ARCH_HAS_PHYS_TO_DMA=y
-CONFIG_ARCH_HAS_SETUP_DMA_OPS=y
-CONFIG_ARCH_HAS_SET_MEMORY=y
-CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
-CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
-CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS=y
-CONFIG_ARCH_HAS_TICK_BROADCAST=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
 CONFIG_ARCH_HIBERNATION_POSSIBLE=y
 CONFIG_ARCH_KEEP_MEMBLOCK=y
 # CONFIG_ARCH_MDM9615 is not set
@@ -34,15 +18,7 @@ CONFIG_ARCH_NR_GPIO=0
 CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
 CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
 CONFIG_ARCH_QCOM=y
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
 CONFIG_ARM=y
 CONFIG_ARM_AMBA=y
 CONFIG_ARM_APPENDED_DTB=y
@@ -75,7 +51,6 @@ CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_MQ_PCI=y
 CONFIG_BOUNCE=y
 # CONFIG_CACHE_L2X0 is not set
-CONFIG_CC_HAS_KASAN_GENERIC=y
 CONFIG_CLKDEV_LOOKUP=y
 CONFIG_CLKSRC_QCOM=y
 CONFIG_CLONE_BACKWARDS=y
@@ -196,48 +171,7 @@ CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_HAS_DMA=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT_MAP=y
-CONFIG_HAVE_ARCH_AUDITSYSCALL=y
-CONFIG_HAVE_ARCH_BITREVERSE=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_ARM_ARCH_TIMER=y
-CONFIG_HAVE_ARM_SMCCC=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_COPY_THREAD_TLS=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
-CONFIG_HAVE_EBPF_JIT=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PCI=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_RSEQ=y
 CONFIG_HAVE_SMP=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
 CONFIG_HIGHMEM=y
 # CONFIG_HIGHPTE is not set
 CONFIG_HWMON=y
@@ -340,6 +274,7 @@ CONFIG_NO_HZ_COMMON=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_NR_CPUS=2
 CONFIG_NVMEM=y
+# CONFIG_NVME_TCP is not set
 CONFIG_OF=y
 CONFIG_OF_ADDRESS=y
 CONFIG_OF_EARLY_FLATTREE=y
@@ -372,6 +307,7 @@ CONFIG_PHYLIB=y
 CONFIG_PHYLINK=y
 # CONFIG_PHY_QCOM_APQ8064_SATA is not set
 CONFIG_PHY_QCOM_IPQ806X_SATA=y
+# CONFIG_PHY_QCOM_IPQ806X_USB is not set
 # CONFIG_PHY_QCOM_PCIE2 is not set
 # CONFIG_PHY_QCOM_QMP is not set
 # CONFIG_PHY_QCOM_QUSB2 is not set

target/linux/ramips/dts/mt7621_tenbay_t-mb5eu-v01.dts

@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "tenbay,t-mb5eu-v01", "mediatek,mt7621-soc";
+	model = "Tenbay T-MB5EU-V01";
+
+	aliases {
+		led-boot = &led_green;
+		led-failsafe = &led_red;
+		led-running = &led_blue;
+		led-upgrade = &led_red;
+		label-mac-device = &wan_port;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		bootargs-override = "console=ttyS0,115200";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		led_blue: blue {
+			label = "blue";
+			gpios = <&aw9523 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led_red: red {
+			label = "red";
+			gpios = <&aw9523 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led_green: green {
+			label = "green";
+			gpios = <&aw9523 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <50>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&button_pins>;
+
+		reset {
+			label = "reset";
+			gpios = <&aw9523 9 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&aw9523 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	i2c-gpio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "i2c-gpio";
+		gpios = <&gpio 7 GPIO_ACTIVE_HIGH &gpio 8 GPIO_ACTIVE_HIGH>;
+		i2c-gpio,delay-us = <10>;
+
+		aw9523: gpio-expander@5b {
+			compatible = "awinic,aw9523-pinctrl";
+			reg = <0x5b>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&aw9523 0 0 16>;
+
+			reset-gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
+
+			button_pins: button-pins {
+				pins = "gpio8", "gpio9";
+				function = "gpio";
+				bias-pull-up;
+				drive-open-drain;
+				input-enable;
+			};
+
+			led_pins: led-pins {
+				pins = "gpio0", "gpio1", "gpio11";
+				function = "gpio";
+				input-disable;
+				output-low;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie1 {
+	wifi@0,0 {
+		reg = <0x0 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x0>;
+	};
+};
+
+&gmac0 {
+	mtd-mac-address = <&factory 0x4>;
+};
+
+&switch0 {
+	ports {
+		wan_port: port@0 {
+			status = "okay";
+			label = "wan";
+			mtd-mac-address = <&factory 0x28>;
+		};
+
+		port@1 {
+			status = "okay";
+			label = "lan1";
+		};
+
+		port@2 {
+			status = "okay";
+			label = "lan2";
+		};
+
+		port@3 {
+			status = "okay";
+			label = "lan3";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "lan4";
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "uart3";
+		function = "gpio";
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "u-boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "product";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			factory: partition@50000 {
+				label = "factory";
+				reg = <0x50000 0x40000>;
+				read-only;
+			};
+
+			partition@90000 {
+				compatible = "denx,fit";
+				label = "firmware";
+				reg = <0x90000 0xf70000>;
+			};
+		};
+	};
+};

target/linux/ramips/image/mt7621.mk

@@ -1200,6 +1200,18 @@ define Device/telco-electronics_x1
 endef
 TARGET_DEVICES += telco-electronics_x1
 
+define Device/tenbay_t-mb5eu-v01
+  $(Device/dsa-migration)
+  DEVICE_VENDOR := Tenbay
+  DEVICE_MODEL := T-MB5EU-V01
+  DEVICE_DTS_CONFIG := config@1
+  DEVICE_PACKAGES += kmod-mt7915e kmod-usb3
+  KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  IMAGE_SIZE := 15808k
+  SUPPORTED_DEVICES += mt7621-dm2-t-mb5eu-v01-nor
+endef
+TARGET_DEVICES += tenbay_t-mb5eu-v01
+
 define Device/thunder_timecloud
   $(Device/dsa-migration)
   $(Device/uimage-lzma-loader)

target/linux/ramips/mt7620/config-5.10

@@ -148,6 +148,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/mt7620/config-5.4

@@ -150,6 +150,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/mt7621/config-5.10

@@ -102,6 +102,7 @@ CONFIG_HAS_IOPORT_MAP=y
 CONFIG_HIGHMEM=y
 CONFIG_I2C=y
 CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_GPIO=y
 CONFIG_I2C_MT7621=y
 CONFIG_INITRAMFS_SOURCE=""
 CONFIG_IRQCHIP=y
@@ -212,6 +213,7 @@ CONFIG_PHYLIB=y
 CONFIG_PHYLINK=y
 # CONFIG_PHY_RALINK_USB is not set
 CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AW9523=y
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_PINCTRL_SX150X=y

target/linux/ramips/mt7621/config-5.4

@@ -100,6 +100,7 @@ CONFIG_HIGHMEM=y
 CONFIG_HZ_PERIODIC=y
 CONFIG_I2C=y
 CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_GPIO=y
 CONFIG_I2C_MT7621=y
 CONFIG_INITRAMFS_SOURCE=""
 CONFIG_IRQCHIP=y
@@ -202,6 +203,7 @@ CONFIG_PHYLIB=y
 CONFIG_PHYLINK=y
 # CONFIG_PHY_RALINK_USB is not set
 CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AW9523=y
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_PINCTRL_SX150X=y

target/linux/ramips/mt76x8/config-5.10

@@ -143,6 +143,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/mt76x8/config-5.4

@@ -143,6 +143,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/patches-5.10/405-mtd-spi-nor-Add-support-for-BoHong-bh25q128as.patch

@@ -0,0 +1,75 @@
+From 52d14545d2fc276b1bf9ccf48d4612fab6edfb6a Mon Sep 17 00:00:00 2001
+From: David Bauer <mail@david-bauer.net>
+Date: Thu, 6 May 2021 17:49:55 +0200
+Subject: [PATCH] mtd: spi-nor: Add support for BoHong bh25q128as
+
+Add MTD support for the BoHong bh25q128as SPI NOR chip.
+The chip has 16MB of total capacity, divided into a total of 256
+sectors, each 64KB sized. The chip also supports 4KB sectors.
+Additionally, it supports dual and quad read modes.
+
+Functionality was verified on an Tenbay WR1800K / MTK MT7621 board.
+
+Signed-off-by: David Bauer <mail@david-bauer.net>
+---
+ drivers/mtd/spi-nor/Makefile |  1 +
+ drivers/mtd/spi-nor/bohong.c | 21 +++++++++++++++++++++
+ drivers/mtd/spi-nor/core.c   |  1 +
+ drivers/mtd/spi-nor/core.h   |  1 +
+ 4 files changed, 24 insertions(+)
+ create mode 100644 drivers/mtd/spi-nor/bohong.c
+
+--- a/drivers/mtd/spi-nor/Makefile
++++ b/drivers/mtd/spi-nor/Makefile
+@@ -2,6 +2,7 @@
+ 
+ spi-nor-objs			:= core.o sfdp.o
+ spi-nor-objs			+= atmel.o
++spi-nor-objs			+= bohong.o
+ spi-nor-objs			+= catalyst.o
+ spi-nor-objs			+= eon.o
+ spi-nor-objs			+= esmt.o
+--- /dev/null
++++ b/drivers/mtd/spi-nor/bohong.c
+@@ -0,0 +1,21 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Copyright (C) 2005, Intec Automation Inc.
++ * Copyright (C) 2014, Freescale Semiconductor, Inc.
++ */
++
++#include <linux/mtd/spi-nor.h>
++
++#include "core.h"
++
++static const struct flash_info bohong_parts[] = {
++	/* BoHong Microelectronics */
++	{ "bh25q128as", INFO(0x684018, 0, 64 * 1024, 256,
++			    SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
++};
++
++const struct spi_nor_manufacturer spi_nor_bohong = {
++	.name = "bohong",
++	.parts = bohong_parts,
++	.nparts = ARRAY_SIZE(bohong_parts),
++};
+--- a/drivers/mtd/spi-nor/core.c
++++ b/drivers/mtd/spi-nor/core.c
+@@ -2038,6 +2038,7 @@ int spi_nor_sr2_bit7_quad_enable(struct
+ 
+ static const struct spi_nor_manufacturer *manufacturers[] = {
+ 	&spi_nor_atmel,
++	&spi_nor_bohong,
+ 	&spi_nor_catalyst,
+ 	&spi_nor_eon,
+ 	&spi_nor_esmt,
+--- a/drivers/mtd/spi-nor/core.h
++++ b/drivers/mtd/spi-nor/core.h
+@@ -382,6 +382,7 @@ struct spi_nor_manufacturer {
+ 
+ /* Manufacturer drivers. */
+ extern const struct spi_nor_manufacturer spi_nor_atmel;
++extern const struct spi_nor_manufacturer spi_nor_bohong;
+ extern const struct spi_nor_manufacturer spi_nor_catalyst;
+ extern const struct spi_nor_manufacturer spi_nor_eon;
+ extern const struct spi_nor_manufacturer spi_nor_esmt;

target/linux/ramips/patches-5.10/805-pinctrl-AW9523.patch

@@ -0,0 +1,72 @@
+From: AngeloGioacchino Del Regno
+        <angelogioacchino.delregno@somainline.org>
+To: linus.walleij@linaro.org
+Cc: linux-kernel@vger.kernel.org, konrad.dybcio@somainline.org,
+        marijn.suijten@somainline.org, martin.botka@somainline.org,
+        phone-devel@vger.kernel.org, linux-gpio@vger.kernel.org,
+        devicetree@vger.kernel.org, robh+dt@kernel.org,
+        AngeloGioacchino Del Regno
+        <angelogioacchino.delregno@somainline.org>
+Subject: [PATCH v5 1/2] pinctrl: Add driver for Awinic AW9523/B I2C GPIO
+ Expander
+Date: Mon, 25 Jan 2021 19:22:18 +0100
+
+The Awinic AW9523(B) is a multi-function I2C gpio expander in a
+TQFN-24L package, featuring PWM (max 37mA per pin, or total max
+power 3.2Watts) for LED driving capability.
+
+It has two ports with 8 pins per port (for a total of 16 pins),
+configurable as either PWM with 1/256 stepping or GPIO input/output,
+1.8V logic input; each GPIO can be configured as input or output
+independently from each other.
+
+This IC also has an internal interrupt controller, which is capable
+of generating an interrupt for each GPIO, depending on the
+configuration, and will raise an interrupt on the INTN pin to
+advertise this to an external interrupt controller.
+
+Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
+---
+ drivers/pinctrl/Kconfig          |   17 +
+ drivers/pinctrl/Makefile         |    1 +
+ drivers/pinctrl/pinctrl-aw9523.c | 1122 ++++++++++++++++++++++++++++++
+ 3 files changed, 1140 insertions(+)
+ create mode 100644 drivers/pinctrl/pinctrl-aw9523.c
+
+--- a/drivers/pinctrl/Kconfig
++++ b/drivers/pinctrl/Kconfig
+@@ -110,6 +110,24 @@ config PINCTRL_AMD
+ 	  Requires ACPI/FDT device enumeration code to set up a platform
+ 	  device.
+ 
++config PINCTRL_AW9523
++	bool "Awinic AW9523/AW9523B I2C GPIO expander pinctrl driver"
++	depends on OF && I2C
++	select PINMUX
++	select PINCONF
++	select GENERIC_PINCONF
++	select GPIOLIB
++	select GPIOLIB_IRQCHIP
++	select REGMAP
++	select REGMAP_I2C
++	help
++	  The Awinic AW9523/AW9523B is a multi-function I2C GPIO
++	  expander with PWM functionality. This driver bundles a
++	  pinctrl driver to select the function muxing and a GPIO
++	  driver to handle GPIO, when the GPIO function is selected.
++
++	  Say yes to enable pinctrl and GPIO support for the AW9523(B).
++
+ config PINCTRL_BM1880
+ 	bool "Bitmain BM1880 Pinctrl driver"
+ 	depends on OF && (ARCH_BITMAIN || COMPILE_TEST)
+--- a/drivers/pinctrl/Makefile
++++ b/drivers/pinctrl/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_PINCTRL_AXP209)	+= pinctrl-
+ obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
+ obj-$(CONFIG_PINCTRL_AT91PIO4)	+= pinctrl-at91-pio4.o
+ obj-$(CONFIG_PINCTRL_AMD)	+= pinctrl-amd.o
++obj-$(CONFIG_PINCTRL_AW9523)	+= pinctrl-aw9523.o
+ obj-$(CONFIG_PINCTRL_BM1880)	+= pinctrl-bm1880.o
+ obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o
+ obj-$(CONFIG_PINCTRL_DA9062)	+= pinctrl-da9062.o

target/linux/ramips/patches-5.4/405-mtd-spi-nor-Add-support-for-BoHong-bh25q128as.patch

@@ -0,0 +1,34 @@
+From 52d14545d2fc276b1bf9ccf48d4612fab6edfb6a Mon Sep 17 00:00:00 2001
+From: David Bauer <mail@david-bauer.net>
+Date: Thu, 6 May 2021 17:49:55 +0200
+Subject: [PATCH] mtd: spi-nor: Add support for BoHong bh25q128as
+
+Add MTD support for the BoHong bh25q128as SPI NOR chip.
+The chip has 16MB of total capacity, divided into a total of 256
+sectors, each 64KB sized. The chip also supports 4KB sectors.
+Additionally, it supports dual and quad read modes.
+
+Functionality was verified on an Tenbay WR1800K / MTK MT7621 board.
+
+Signed-off-by: David Bauer <mail@david-bauer.net>
+---
+ drivers/mtd/spi-nor/Makefile |  1 +
+ drivers/mtd/spi-nor/bohong.c | 21 +++++++++++++++++++++
+ drivers/mtd/spi-nor/core.c   |  1 +
+ drivers/mtd/spi-nor/core.h   |  1 +
+ 4 files changed, 24 insertions(+)
+ create mode 100644 drivers/mtd/spi-nor/bohong.c
+
+--- a/drivers/mtd/spi-nor/spi-nor.c
++++ b/drivers/mtd/spi-nor/spi-nor.c
+@@ -2233,6 +2233,10 @@ static const struct flash_info spi_nor_i
+ 
+ 	{ "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
+ 
++	/* BoHong Microelectronics */
++	{ "bh25q128as", INFO(0x684018, 0, 64 * 1024, 256,
++			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
++
+ 	/* EON -- en25xxx */
+ 	{ "en25f32",    INFO(0x1c3116, 0, 64 * 1024,   64, SECT_4K) },
+ 	{ "en25p32",    INFO(0x1c2016, 0, 64 * 1024,   64, 0) },

target/linux/ramips/patches-5.4/805-pinctrl-AW9523.patch

@@ -0,0 +1,72 @@
+From: AngeloGioacchino Del Regno
+        <angelogioacchino.delregno@somainline.org>
+To: linus.walleij@linaro.org
+Cc: linux-kernel@vger.kernel.org, konrad.dybcio@somainline.org,
+        marijn.suijten@somainline.org, martin.botka@somainline.org,
+        phone-devel@vger.kernel.org, linux-gpio@vger.kernel.org,
+        devicetree@vger.kernel.org, robh+dt@kernel.org,
+        AngeloGioacchino Del Regno
+        <angelogioacchino.delregno@somainline.org>
+Subject: [PATCH v5 1/2] pinctrl: Add driver for Awinic AW9523/B I2C GPIO
+ Expander
+Date: Mon, 25 Jan 2021 19:22:18 +0100
+
+The Awinic AW9523(B) is a multi-function I2C gpio expander in a
+TQFN-24L package, featuring PWM (max 37mA per pin, or total max
+power 3.2Watts) for LED driving capability.
+
+It has two ports with 8 pins per port (for a total of 16 pins),
+configurable as either PWM with 1/256 stepping or GPIO input/output,
+1.8V logic input; each GPIO can be configured as input or output
+independently from each other.
+
+This IC also has an internal interrupt controller, which is capable
+of generating an interrupt for each GPIO, depending on the
+configuration, and will raise an interrupt on the INTN pin to
+advertise this to an external interrupt controller.
+
+Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
+---
+ drivers/pinctrl/Kconfig          |   17 +
+ drivers/pinctrl/Makefile         |    1 +
+ drivers/pinctrl/pinctrl-aw9523.c | 1122 ++++++++++++++++++++++++++++++
+ 3 files changed, 1140 insertions(+)
+ create mode 100644 drivers/pinctrl/pinctrl-aw9523.c
+
+--- a/drivers/pinctrl/Kconfig
++++ b/drivers/pinctrl/Kconfig
+@@ -109,6 +109,24 @@ config PINCTRL_AMD
+ 	  Requires ACPI/FDT device enumeration code to set up a platform
+ 	  device.
+ 
++config PINCTRL_AW9523
++	bool "Awinic AW9523/AW9523B I2C GPIO expander pinctrl driver"
++	depends on OF && I2C
++	select PINMUX
++	select PINCONF
++	select GENERIC_PINCONF
++	select GPIOLIB
++	select GPIOLIB_IRQCHIP
++	select REGMAP
++	select REGMAP_I2C
++	help
++	  The Awinic AW9523/AW9523B is a multi-function I2C GPIO
++	  expander with PWM functionality. This driver bundles a
++	  pinctrl driver to select the function muxing and a GPIO
++	  driver to handle GPIO, when the GPIO function is selected.
++
++	  Say yes to enable pinctrl and GPIO support for the AW9523(B).
++
+ config PINCTRL_BM1880
+ 	bool "Bitmain BM1880 Pinctrl driver"
+ 	depends on OF && (ARCH_BITMAIN || COMPILE_TEST)
+--- a/drivers/pinctrl/Makefile
++++ b/drivers/pinctrl/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_PINCTRL_AXP209)	+= pinctrl-
+ obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
+ obj-$(CONFIG_PINCTRL_AT91PIO4)	+= pinctrl-at91-pio4.o
+ obj-$(CONFIG_PINCTRL_AMD)	+= pinctrl-amd.o
++obj-$(CONFIG_PINCTRL_AW9523)	+= pinctrl-aw9523.o
+ obj-$(CONFIG_PINCTRL_BM1880)	+= pinctrl-bm1880.o
+ obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o
+ obj-$(CONFIG_PINCTRL_DIGICOLOR)	+= pinctrl-digicolor.o

target/linux/ramips/rt288x/config-5.10

@@ -131,6 +131,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 # CONFIG_PHY_RALINK_USB is not set
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/rt288x/config-5.4

@@ -131,6 +131,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 # CONFIG_PHY_RALINK_USB is not set
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/rt305x/config-5.10

@@ -131,6 +131,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/rt305x/config-5.4

@@ -131,6 +131,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/rt3883/config-5.10

@@ -132,6 +132,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y

target/linux/ramips/rt3883/config-5.4

@@ -133,6 +133,7 @@ CONFIG_PGTABLE_LEVELS=2
 CONFIG_PHYLIB=y
 CONFIG_PHY_RALINK_USB=y
 CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_AW9523 is not set
 CONFIG_PINCTRL_RT2880=y
 # CONFIG_PINCTRL_SINGLE is not set
 CONFIG_RALINK=y