ef20327e33
Specification: SoC: MediaTek MT7628AN RAM: 128M DDR2, ESMT M14D128168A (2Y) Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt, SPI) Switch: MediaTek MT7628AN, 3 ports 100 Mbps WiFi: MediaTek MT7628AN 2.4 GHz 802.11n USB: 1 port USB 2.0 GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power, Internet, Wi-Fi), USB port power controls Disassembly: There are 2 screws at the bottom near the LEDs hidden by rubber mounts. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it. UART Interface: The UART interface can be connected to the 5 pin located between LAN ports and the WAN one. Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND Settings: 115200, 8N1 Flashing via TFTP: 1. Connect your PC and router to the first LAN port, configure PC interface using IP 192.168.1.2, mask 255.255.255.0 2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin) renamed to KN-1221_recovery.bin via TFTP 3. Power up the router while pressing Wi-Fi button 4. Release Wi-Fi button when Power LED starts blinking To revert back to OEM firmware: The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image found on osvault.keenetic.net. When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size. Signed-off-by: Ivan Davydov <lotigara@lotigara.ru> Link: https://github.com/openwrt/openwrt/pull/18164 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0