TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
Strip off initial leading blanks and tabs from scripts and script
fragments that are supplied by the package's Makefile. Specifically,
the script included in the postrm must be left justified so that
the shebang is in the first column.
Fixes: https://github.com/openwrt/openwrt/issues/17439
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17440
Signed-off-by: Robert Marko <robimarko@gmail.com>
If CC is explicitly set to a non default value, TF-A keeps this value.
Otherwise it assigns generic default value.
As the build bot set CC=/usr/bin/gcc-10, TF-A uses it which causes a
compile issue.
So unset CC before compiling.
It's a new behavior since v2.12. A part of the explanation is available in
this commit [1].
[1] e01c71266f
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17465
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since v2.12, TF-A automatically selects the no-warn-rwx-segments option if
needed.
So move this hack to the package Makefiles.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.65
Update to checksum only/no patches required a rebase.
Per the changelog, this is a trivial upstream bump with only 4
commits, 2 of which being reverts.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17217
Signed-off-by: Robert Marko <robimarko@gmail.com>
mkits.sh creates a root.*.pagesync file with padding, which is global, and
the generated .its files reference it. Since dtc reads this file, it must
not run at the same time as mkits.sh
Fixes generating itb images with broken rootfs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Fixes: #17146
Link: https://github.com/openwrt/openwrt/pull/17151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce package flag MESON_USE_STAGING_PYTHON which allows packages
to be built with the OpenWrt-built python3/host instead of relying on the
buildhost's Python distribution.
This is useful for packages using Meson which require additional Python
modules during build.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, in case when a package in the device package list is marked with
the "-"" prefix meaning that its supposed to be removed for that device but
it was not actually previously built it will cause the APK to error out it
and thus image generation will also fail.
So, lets do what OPKG build step does and supress the error with the "-"
prefix in make.
Fixes: #17103
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17106
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is required for upcoming Keenetic KN-3911 support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set MESON_ARGS and MESON_HOST_ARGS when calling ninja for building.
This is required eg. to be able to set PYTHONPATH= not just for the
Meson (==configure) run but also for the build phase itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.
Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.
This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
procd-seccomp (no such package):
required by: base-files-1637~52b6c92479[procd-seccomp]
Fixes: 4c65359af49b ("build: fix including busybox, procd and apk/opkg in imagebuilder")
Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a generic template include/optee-os.mk to build OP-TEE.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, postrm scripts are not being executed when package is removed
with APK since they are not being included at all.
So, lets use APK-s support for post-deinstall scripts and ship our postrm
scripts if packages define them.
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17023
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, when you install a package that ships uci-defaults scripts they
are not getting executed during package installation.
For example, if you install a new LuCI theme it ships a uci-defaults script
to add it to the UCI LuCI config so the theme is actually selectable but
that does not happen until the device is rebooted so that uci-defaults
script is actually executed.
It turns out that the recipe for post-install is the issue since it will
include contents of postinst-pkg before the call to default_postinist.
This is an issue since postinst-pkg will exit with code 0 before we ever
reach the call to default_postinist.
So, lets simply make the call to default_postinist before postinst-pkg
inclusion which is what OPKG based installation does.
The same issue affects pre-deinstall script but its not actually being hit
since we dont seem to be actually even generating prerm-pkg scripts but
lets fix this theoretical issue as well.
Fixes: #16987
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17023
Signed-off-by: Robert Marko <robimarko@gmail.com>
We have a lot of script-only packages that are universal for all arch-s
and those set PKGARCH:=all to indicate it.
Unfortunately, APK expects architecture to be set to "noarch" instead to
indicate that its universal so instead of having to update all packages
that set PKGARCH:=all and thus break OPKG lets simply translate "all" to
"noarch" when generating the APK package.
This will be required as soon we update APK to include [1] as it will start
enforcing package architecture checks.
[1] c1a3e69f24
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17015
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, trying to use APK to install a package that has a dependency on
a virtual package that needs to be resolved via 'provides' it will fail if
package does not have 'DEFAULT_VARIANT:=1' like:
apk add usbutils
ERROR: unable to select packages:
libudev (virtual):
note: please select one of the 'provided by' packages explicitly
provided by: libudev-zero
required by: usbutils-017-r1[libudev]
Issue is that we dont set 'provider_priority' that APK uses to break ties
when choosing a virtual package to satisfy a dependency and thus despite
only one package providing the dependency it will still end up with a tie
and just error out.
So, lets simply fix this by providing a default value for
'provider_priority' when 'DEFAULT_VARIANT' is not set and then APK will
be able to resolve dependencies.
Fixes: #16976
Link: https://github.com/openwrt/openwrt/pull/17008
Signed-off-by: Robert Marko <robimarko@gmail.com>
