Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.83..HEAD
(HEAD -> 08d4e8f52256bd422d8a1f876411603f627d0a82)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 251f76c1c67d62c585d799c38dab31e1385d2ad5)
d8b43985e4d7 ubus: fix token_create policy
7326459bd743 ubus: dump service information on network_get
6c9c8fbd8128 service: add @all as alias for all members, unless defined differently
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 84909c62c8455a08fb8bb29bd7809ab22c927bf0)
The M1300 v2 is similar to the WR1300 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7621
- MT7603E (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:1C
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WAN (top connector) is label +2, e.g. xx:xx:xx:xx:xx:1E
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WLAN (5G) is the same as WAN, e.g. xx:xx:xx:xx:xx:1E
UART:
- is available via the pin holes on the board
- From inner to outer pin: TX, RX, GND, VCC
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 3) and White (GPIO 4)
- There are two buttons: Reset (GPIO 8) and WPS (GPIO 10)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- The migration image is also available here until a image is provided by Cudy: https://github.com/RolandoMagico/openwrt-build/releases/tag/M1300_Build_20240222
- File: openwrt-ramips-mt7621-cudy_m1300-v2-squashfs-flash-signed.bin
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- In the migration image, LAN and WAN are swapped. Computer must be connected to the other port after flashing
- OpenWrt is now accessible via 192.168.1.1
- After flashing an up to date OpenWrt image, LAN and WAN settings are again the same as in the OEM firmware
- So use the other connector again
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the LAN port (lower port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18139
(cherry picked from commit 8a7863767056ca0dec69a6b383b6e0c0d5fc3af7)
Link: https://github.com/openwrt/openwrt/pull/18204
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes are only for the WRT1900X and WRT1200AC.
It contains:
Deletes the driver's ability to modify the debit table.
Remove skb_get(done_skb) in txdone
Reworking ISR
clean code
Napi replaces tasklet
Add rx_decrypt feature
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17997
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18145
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Genexis Pulse EX400 / Inteno Pulse EX400. A branded
variant for the Finnish ISP DNA has already been added in fea2264d9fdd
(ramips: mt7621: Add DNA Valokuitu Plus EX400, 2023-07-31). This commit
adds support for the generic variants with Inteno and Genexis branding.
Inteno changed its name to Genexis and both brandings exist.
In terms of electronics, there is no difference between the DNA-branded
version and other brandings. LED markings on the case are different,
though. While the DNA-version has a "software-update" LED, the other
versions have a WPS LED. To reduce user confusion, create a separate
image.
Add the different device-tree with the different LED and rename things
to work the same way for both variants.
Specifications:
- Device: Genexis Pulse EX400 / Inteno Pulse EX400
- SoC: MT7621A
- Flash: 256 MB NAND
- RAM: 256 MB
- Ethernet: Built-in, 2 x 1 GbE
- Wifi: MT7603 2.4 GHz 2x2 MIMO, MT7615 5 GHz 4x4 MU-MIMO
- USB: 1x 2.0
- LEDs (GPIO): green/red status, green WPS
- LEDs (SX9512, unsupported): Broadband, Wi-Fi 2.4G, Wi-Fi 5G
- Buttons (GPIO): Reset
- Buttons (SX9512, unsupported): Wi-Fi 2.4G, Wi-Fi 5G, WPS
MAC addresses:
- LAN: U-Boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access, booting can be halted to U-boot by pressing
any key. TFTP and flash writes are available, but only the first one has
been tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI, or from the U-Boot recovery UI, install the
OpenWrt factory image. Alternatively, ssh to the device and use
sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
(cherry picked from commit 3e7337feead8e0a0f5a05f5b91d7d0fd7f14ec56)
Link: https://github.com/openwrt/openwrt/pull/18238
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move common definitions for DNA Valokuitu Plus EX400 to a dtsi include.
This is in preparation of adding the non-branded variant of the device
produced by Genexis / Inteno in the next commit. The device with DNA
branding differs in the LED labling on the device.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
(cherry picked from commit e8603f3b5a15856fccee2e02a5406ca9c8b2ba1d)
Link: https://github.com/openwrt/openwrt/pull/18238
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt 14.07 OEM
customized version
WARNING: The original firmware device tree is common to multiple
boards, and the device tree name is H9350. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7620A
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN, 4x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (RUN): GPIO/26 active-low
Ethernet: 1x WAN, 4x LAN
Modem 1: GPIO/66 active-low
RF 1 (Modem 1 Signal): GPIO/67 active-low
Modem 2: GPIO 71 active-low
RF 2 (Modem 2 Signal): GPIO/24 active-low
WLAN: GPIO/72 active-low
WPS: GPIO/12 active-low
- Button:
WPS / RESET: GPIO/34 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/62 mode=toggle timeout=1s
- PCIe: 2x miniPCIe for modem
- SIM Slots: 2x SIM Slots
Issue:
- No factory partition, eeprom is located
at /lib/firmware/mt7620a.eeprom
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put rootfs into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press Ctrl+C to break auto boot.
5. Use `system 6` command and follow the instruction to set device
and tftp server IP address and input the rootfs file name.
U-boot will then load the rootfs and write it into
the flash.
6. Use `system 1` command and follow the instruction to set device
and tftp server IP address and input the firmware file name.
U-boot will then load the firmware once.
7. Login to LuCI and use LuCI upgrade firmware.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8922-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17472
Link: https://github.com/openwrt/openwrt/pull/18221
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6a1bdcf545eec8f9ed5130e7f5794fca6ee54cb3)
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
(cherry picked from commit 96c6608346758ceffebf30d74cab00db58874bb9)
[sync uboot defconfigs with 24.10 branch, change apk to opkg]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18218
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Trying to tcpdump DSA conduits results in errors such as
"unsupported DSA tag: mtk".
Backport two commits adding support for various DSA tags to libpcap.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fad94e8cda573389164827dc74e583d10eeae2e5)
Currently, enabling USB, BT or Netfilter support after initial compilation
will not trigger a rebuild, so add the missing PKG_CONFIG_DEPENDS so
that rebuild gets triggered.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit fe37574be63ef7c6c1c1e611f052ed25c99a8aa1)
Backport FORESEE NAND chip support from upstream Linux. The newly
introduced FORESEE F35SQA001G was found on the Xiaomi AX3000T.
Signed-off-by: Erik Servili <serverror@serverror.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 302c717aa3a434676a32a4dde8b10ec2c03798b5)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB DDR3 or DDR4
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Get the SN of the device from web interface or the label on the back of the device.
3. Calculate configuration decryption password:
Command "eval" is necessary here as the encryption implentation treats '$...' as (empty) variables.
decpwd="$(eval echo $(openssl passwd -1 -salt aV6dW8bD "your_device_sn"))"
4. Decrypt the configuration:
openssl aes-256-cbc -d -pbkdf2 -k "$decpwd" -in cfg_export_config_file.conf -out cfg_export_config_file.conf.dec
5. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf.dec
6. Edit 'etc/shadow', update (remove) root password: 'root::19179:0:99999:7:::'
7. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
8. Repack the configuration:
tar -zc etc/ | openssl aes-256-cbc -pbkdf2 -k "$decpwd" -out cfg_export_config_file.conf
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
9. Upload new configuration via web interface, now you can connect to
CMCC RAX3000Me via telnet.
(Big thanks to https://github.com/lyq1996 who reverse engineered the encryption method)
Check flash type:
If '/dev/mmcblk0' exists on the device, it's eMMC version.
If '/dev/mtd0' exists on the device, it's NAND version.
eMMC Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Write new FIP:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
NAND Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'Factory' part.
2. Write new BL2 and FIP:
If your device HAS USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-bl31-uboot.fip FIP
If your device DOES NOT have USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 57f31cd5b11cb7e590c330845ec74ffa2d6eb13e)
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd85 ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/18182
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5013efc4f907550fadbf15e2fb1bdb2ead3325db)
Prior to commit 8a7d12d674,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
[1] https://lore.kernel.org/all/Z00udyMgW6XnAw6h@atmark-techno.com/
[2] https://lore.kernel.org/all/20241203130457.904325-1-asmadeus@codewreck.org/
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17757
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ecd609f509f29ed1f75db5c7a623f359c64efb72)
`ucv_array_set` releases the array's reference to the object being cleared.
If this is the last reference to the object, it will be freed, making our
pointer `val` invalid.
To avoid this, we need to obtain our own reference to the object so we
can safely return `val`.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit 6a10da2934441a59283394a84917edf4983e3043)
Since `wpa_ucode_registry_add` collects its own reference to the values added, the
two functions `hostapd_ucode_bss_get_uval` and `hostapd_ucode_iface_get_uval` would
sometimes return a referenced object (from `uc_resource_new`) and sometimes return
an unreferenced object (from `wpa_ucode_registry_get`). Now, both functions always
return a referenced object.
This change also indirectly fixes `hostapd_ucode_bss_get_uval`, ensuring it now
always returns a referenced object.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7729f960933a03c9eebd2b65a695ea57718ccb77)
Remove extra ucv_get calls when passing a referenced value to an object
without using it further.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 22eaf1864731dd29918357b26565dbd9420fd314)
This fixes a common reference counting bug typically along the lines of:
```
uc_value_push(ucv_get(ucv_string_new(...)));
```
This would leave our new string with a reference count of 2, one from
the construction of the string, the other from `ucv_get`. This would
prevent the strings from being correctly cleaned up when it goes out
of scope.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit f79968ee0f76c41414fb0c08980b9c2a259964d3)
When a feed has submodules, all its submodules are fully cloned whereas
the feed itself is shallowed. Let's be consistent and perform shallow clones
as well for the submodules.
Signed-off-by: Cedric CHEDALEUX <cedric.chedaleux@orange.com>
Link: https://github.com/openwrt/openwrt/pull/18003
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9ec32cfb2733856a2ab4caee07d9b3297568381d)
When a feed is referenced with a specific commit (i.e. <git_url>^<sha1>),
a full clone was performed and a branch was created from the sha1
and named with the sha1. Other git clones operations are shallowed.
As Git does not support clone at a specific commit, let's first perform
a shallow clone to latest commit, then fetch the relevant commit and
finally checkout it (no more 'pseudo' branch).
It saves bandwith and significantly speeds up the feed update process.
Signed-off-by: Cedric CHEDALEUX <cedric.chedaleux@orange.com>
Link: https://github.com/openwrt/openwrt/pull/18003
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 32d0a57dc10811a24816e51f10e55963f40fe462)
kmod-mmc-mtk does not work well on this board, switch back to deprecated
kmod-sdhci-mt7620 driver for now.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
75a236be122a service: add missing null pointer check
f5341f327539 ubus: add api for generating and validating security tokens
3fab99eab4d5 add udebug support
28d86bd30e97 pex: only respond to update requests when we have network data
8e6f37cc361e pex-msg: ignore no-data responses if version is zero
12e6cf7f63e1 pex: create pex host from update responses
edc8fdae463a ubus: show the local addresses in network status
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit ce68f61cb67a4701a108f838f510e72ca63ed78e)
ethtool since version 6.9 introduced support for getting/setting RSS
input transformation supported in Linux since version 6.8.
The now changed kernel ioctl ABI, however, cannot be detected from
userland, and ethtool since version 6.9 simply assumes that a previously
reserved field is now used to set the input transformation.
Unfortunately the default value RXH_XFRM_NO_CHANGE (0xff) used by ethtool
userland creates an incompatibility with older kernels which cannot be
resolved easily without introducing even more ABI breakage.
Work-around the issue and fix support for --set-rxfh and --set-rxfh-indir
ethtool userland tool commands by making the support for input_xfrm
conditional on compile time, and keep it disabled for Linux 6.6.
Fixes: 8c2dcd1518 ("ethtool: update to 6.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 3a7467ffde413677de5465dde78a62dfa8d6774f)
Version 6.11 - October 8, 2024
* Feature: cmis: print active and inactive firmware versions
* Feature: flash transceiver module firmware (--flash-module-firmware)
* Feature: add T1BRR 10Mb/s mode to link mode tables
* Feature: support for disabling netlink from command line
* Fix: fix lanes parameter format specifier
* Fix: add missing clause 33 PSE manual description
* Fix: qsf: Better handling of Page A2h netlink read failure
* Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x)
* Misc: man page formatting fix
* changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406
Tested on gl.inet MT6000, retrieve ring count is now working
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17607
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9454331b7fc896704a2c60b28767c282eb9ca0bd)
