Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD -> bba53a117a4a5c29da892962332ff1605990e17a)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This brings up a serial console on the USB device port of
the DNS-313 by:
- Activating the usbgadget feature
- Selecting the usbgadget-acm package
- Adding an inittab that opens a console at ttyGS0 which is
the device side of ttyACMn of a connected host
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-4-d84de8e86931@linaro.org/
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath9k base starts at 512. This is a problem as it uses gpio_request_one
to request the GPIO, which is legacy API.
This upstream pending patch needs to also be ported to mac80211.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
PHY2 led1 is configured to control PHY1's LED. Change it to PHY2.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18361
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds support for setting bridge port learning and isolation flags on
ipq40xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6c0 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch adds support for D-Link DGS-1210-26 rev. F1
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash (MX25L25635E)
* 24 x 10/100/1000BASE-T ports
* 2 x SFP ports
* Power LED
* Reset button on front panel
Installation using OEM webinterface
-----------------------------------
1. Make sure you are running OEM firmware from secondary slot. If not, switch to image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image squashfs-factory_image1.bin via Tools > Backup / Upgrade Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot from image1
4. Tools > reboot
Known working firmware version for this procedure: 6.20.007
Installation using TFTP and serial console
------------------------------------------
1. Prepare a TFTP server with the OpenWrt *initramfs-kernel.bin and assign it an IP from 10.90.90.0/24 (except 10.90.90.90)
2. Connect the TFTP server to one of switch's ports
3. Connect to the serial console (115200 baud) and power on the switch
4. Press the ESC key once you see "Hit Esc key to stop autoboot" in the console output
5. Press CTRL+C keys to get into the real U-Boot prompt
6. Init the network with the command "rtk network on"
7. Load the OpenWrt image with the command "tftpboot 0x8f000000 <TFTP_SERVER_IP>:<IMAGE_FILE>"
(<TFTP_SERVER_IP> is the TFTP server's IP, e.g. 10.90.90.100; <IMAGE_FILE> is the name of the image provided by the TFTP server)
8. Boot the OpenWrt image with the command "bootm"
9. Browse to https://192.168.1.1/cgi-bin/luci/admin/system/flash
10. Upload the the OpenWrt *squashfs-sysupgrade.bin to the switch
11. Wait for it to reboot
Signed-off-by: Christian Steiner <christian.steiner@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/18378
Signed-off-by: Sander Vanheule <sander@svanheule.net>
NEC Aterm WG2200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 4T4R (Qualcomm Atheros QCA9984)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 12x/4x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- Power : 12 VDC, 1.5 A (Max: 20 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image:
1. Connect and open serial console
2. Power on WG2200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Rplace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the Diodes PI4IOE5V9539LE I2C Expander chip.
(compatible with NXP PCA9539)
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI of all versions, and
initramfs-factory.bin image of OpenWrt has the larger block data for
initramfs image. So that image cannot be applied to the stock WebUI
at all.
MAC addresses:
LAN : 98:F1:99:xx:xx:7C (config, 0x6 (hex))
WAN : 98:F1:99:xx:xx:7D (config, 0xc (hex))
2.4 GHz: 98:F1:99:xx:xx:7E (config, 0x0 (hex))
5 GHz : 98:F1:99:xx:xx:7F (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add more DT labels and move a USB hub node to dts files of Aterm devices
as a preparation for adding support of Aterm WG2200HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
The built-in watchdog is redundant when the device has an external
GPIO based hardware watchdog. And there is a conflict that both of
them will attempt to register the same device entry in sysfs. This
resulted in the built-in watchdog being unable to be activated.
This patch explicitly disables the built-in watchdog for devices
that use GPIO watchdog to fix the error:
[ 1.779206] ath79-wdt 18060008.wdt: unable to register misc device, err=-16
[ 1.786355] ath79-wdt: probe of 18060008.wdt failed with error -16
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18395
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.
A similiar change has been previously applied for RTL83xx in commit
cd958d945be0 ("realtek: 6.6: refactor mac config and link up for
RTL83xx").
Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The generic target configuration activates the
CONFIG_LEDS_CLASS_MULTICOLOR option. Do not deactivate it for the stm32
target.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This restores sysupgrade support
Since OpenWrt 23.05, the firmware selector no longer provides sysupgrade
images for RE450 V1 & V2 and RE355 v1 due to image size constraints
(~5.7MB limit), making the generic build unusable.
This commit moves RE450 V1 & V2 to the tiny target, enabling:
- Smaller image builds within the flash size limit.
- Restored sysupgrade support via the firmware selector.
- A secure-by-default wireless setup while allowing full management via UCI.
- Officially supported images, reducing the need for custom (potentially insecure) builds.
This ensures users can install a functional OpenWrt build without compromising security defaults.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
[Squashed the commits together and just copied the target definition
from the generic subtarget.]
Link: https://github.com/openwrt/openwrt/pull/18126
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.
When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358d5 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79ccf ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
This reverts commit 7aa3dfdbda829c04475cffbd6708f1ff96e4849b.
As the kernel is now fixed with ecd609f509
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18380
Signed-off-by: Robert Marko <robimarko@gmail.com>
Only force compat_version to 1.2 if it was less than 1.2 before, as changes
1.1 and 1.2 were bootloader-related and a completed boot indicates that the
changes have been completed. Newer compat version 1.3 indicates a config change
and should not be forced on boot.
Fixes: 84fc59c0d5 ("mediatek: filogic: bpi-r3: set netdev-name for sfp1 port")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Patches 751-03 and 751-04 as a result of commit 6407ef8d2bcb4a0a6284de09cd77bd1868c1d6ea
were incorrectly placed in the backport folder.
So they return to their proper place.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
