RNDIS interface name change from usb0 to eth1
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18298
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using the pending ascii-eq-delim-env4 driver is a better way to read mac addresses since no
extra config is required
The change is like eacc4d8c9b31ac17df034d2140558bdaaa56c16b, except for using smem for devinfo
thanks to @musashino205 for pointing out the simplification that removes
the extra partition
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18186
Signed-off-by: Robert Marko <robimarko@gmail.com>
With this patch, iw can now scan APs in the 6 GHz band and shows
their operation parameters:
~~~
6 Ghz Operation Information: 0x0103070f06
Primary Channel: 1
Channel Width: 80+80 or 160 MHz
Regulatory Info: 0
Center Frequency Segment 0: 7
Center Frequency Segment 1: 15
Minimum Rate: 6
~~~
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18240
Signed-off-by: Robert Marko <robimarko@gmail.com>
arcadyan_mozart was incorrectly placed below asus devices
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18331
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for WAX620 and WAX630 which is accepted by the stock UI.
Must use 'Boot up Backup Firmware' button on stock upgrade page after install and reboot to swap partitions.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18334
Signed-off-by: Robert Marko <robimarko@gmail.com>
`bootargs = "console=ttyS0,57600";` is already defined on all
ramips target SoCs' dtsi. We don't need to override it with the
same value.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/18303
Signed-off-by: Robert Marko <robimarko@gmail.com>
ChangeLog
417c2e3 libtracefs: version 1.8.1
41efd9e libtracefs: Add meson build targets to Makefile
310b796 libtracefs utest: Add better logic to cause missed events
b589e32 libtracefs: Add cpu-map sample to trace mapped buffer
4ede86e libtracefs: Enable mmapped ring buffer
e6737d4 libtracefs: Initialize val in build_filter()
590e452 libtracefs: Close dir in the error path in tracefs_event_systems()
0309a87 libtracefs: Close dir in the error path in tracefs_system_events()
f34fb1f libtracefs: Prevent memory leak in tracefs_dynevent_get_all()
48e906b libtracefs: my_yyinput() should return 0 when no data can be read
5e5b2a7 libtracefs: Prevent memory leak in tracefs_instance_create()
8f2593f libtracefs: Prevent a memory leak in open_cpu_files()
7d77b83 libtracefs: Prevent a memory leak in tracefs_system_events()
7fcd8d2 libtracefs: Prevent a memory leak in add_func_str()
a01d0ba libtracefs: Don't leak socket file descriptor in open_vsock()
efdf7f7 libtracefs: Prevent memory leak in tracefs_event_systems()
2342293 libtracefs: Prevent a memory leak in tracefs_synth_add_end_field()
1c95394 libtracefs: Prevent a memory leak in update_fields()
6b35665 libtracefs: Prevent memory leak in append_filer()
aecc0b7 libtracefs: Call va_end() before exiting tracefs_hist_set_sort_key()
a5e37f7 libtracefs: Add trace-mmap.c to meson build
8f62e96 libtracefs meson: Use SemVer in the build description
e04fa01 meson: Add utest option
fb213a4 libtracefs: Update trace_buffer_meta
04505a0 libtracefs utest: Include libgen.h for basename()
7b4a9c9 libtracefs utest: Define _LARGEFILE64_SOURCE for lseek64() with musl
ba75081 libtracefs utest: Add PATH_MAX if it is not already defined
5f27b7f libtracefs: Update the kbuf for previous read in trace_mmap_load_subbuf()
73ac9c1 libtracefs: Fix tracefs_instance_reset() of triggers
7d15d77 libtracefs meson: build tracefs-mmap by default
Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>
ChangeLog:
bd47bd5 libtraceevent: 1.8.4
fe0bc49 libtraceevent: Print function pointer address when TEP_EVENT_FL_PRINTRAW is specified
f2224d5 libtraceevent: Have sizeof() parsing handle u8/s8 through u64/s64
5f570de libtraceevent: Print arrays like Linux does
645a883 libtraceevent: 1.8.3
d4c1fb4 libtraceevent: Add meson build targets to Makefile
c3dc220 libtraceevent: Fix a double free in process_op()
021da90 libtraceevent: Do not return a local stack pointer in get_field_str()
340e2e6 libtraceevent: Have unit test fail when any tests fail
c84155f libtraceevent: prevent a memory leak in tep_plugin_add_option()
03551eb libtraceevent: Prevent a memory leak in process_fields()
34ece90 libtraceevent: Close shared object in the error path of load_plugin()
8802f0f libtraceevent: Avoid a simple asprintf case
76a0eb8 libtraceevent: Fix event-parse memory leak in process_cond
5bc98bd libtraceevent: Have single quotes represent characters
ec8e0cc libtraceevent: Fix tests running on big endian arch
60ed6c3 libtraceevent: build: Various fixes for the Meson build of libtraceevent
0351241 libtraceevent utest: Include libgen.h for basename() with musl
Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Currently, both envtools and the rest of U-Boot tools are being built
regardless if the dumpimage package has been selected.
This will fail if only envtools are selected since the rest of tools
require OpenSSL while envtools do not require them.
So, only build tools if dumpimage is selected.
Fixes: 46e376c93514 ("uboot-tools: migrate uboot-envtools to uboot-tools")
Fixes: #18327
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/18329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make cpufreq work on different IPQ60xx SoC.
Also rebase ipq6018-cp-cpu.dtsi for mp5496.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh device tree, remove the useless sdhc2 aliases.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the minimal change for the upcoming patches.
Refresh the device tree of ipq807x at the same time.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because of the dt-bindings error, these patches have not
been merged yet, and the driver part is fine.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be used by GL.iNet devices from other target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Do not verify the format of TLV. Leave that to lldpd.
These lldpd config entries:
config custom-tlv
list ports 'eth0'
option tlv 'replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55'
config custom-tlv
option tlv 'oui 33,44,44 subtype 232'
list ports 'br-lan'
list ports 'eth0'
config custom-tlv # oui-info truncated
option tlv 'add oui 33,44,33 subtype 66 oui-info 5555555555'
config custom-tlv
option tlv 'add oui 33,44,31 subtype 44'
config custom-tlv # invalid oui
option tlv 'add oui 3322 subtype 79'
config custom-tlv # invalid oui
option tlv 'oui 3312 subtype 74'
Produce the following lldpd.conf content:
configure ports eth0 lldp custom-tlv replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55
configure ports br-lan,eth0 lldp custom-tlv oui 33,44,44 subtype 232
configure lldp custom-tlv add oui 33,44,33 subtype 66 oui-info 5555555555
configure lldp custom-tlv add oui 33,44,31 subtype 44
configure lldp custom-tlv add oui 3322 subtype 79
configure lldp custom-tlv oui 3312 subtype 74
And lldpd (v1.0.13 on v22) logs the following:
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op replace oui 33:44:55 subtype fe
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:44 subtype e8
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3322'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3312'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: lldpd should resume operations
( The last two TLV are invalid: their oui must be three hex bytes, comma
separated. Only the first hex byte of oui-info 5555555555 is used )
Depends on #14867 and its release version bump
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>
where csv = comma separated value(s)
Make the function more generic. Can use it for not only 'config'.
Now it can be used to parse interfaces for additional lldpd settings,
e.g. custom-tlv.
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add uboot-tools stub package skeleton which will replace uboot-envtools
and also provide target-builds for other U-Boot tools.
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
As described in #13873, from 23.05.0 onwards logging to a file on an
external filesystem fails under some conditions.
This occurs because the log initscript had code added to prevent start
logging to an external filesystem on boot, and added a trigger to start
said logging when the external filesystem gets mounted.
The issue is that for filesystems mount with fstab uci, the fstab
scripts runs at START=11, while log runs at START=12, which means the
external filesystem may already be mounted by the time the log initscript
runs. Since the external filesystem is already mounted it does not
trigger a hotplug event to trigger the trigger to start logging. This
combination means the logging never automatically starts when the log
file is on an external filesystem.
We therefore add a check for the presence of a mounted filesystem when
the log file is being sent to an fstab mounted filesystem. If the
filesystem is mounted, we don't skip starting logging during boot.
If the filesystem is not mounted then file logging is not started and
the trigger will start the logging when the filesystem is mounted.
Signed-off-by: Daniel F. Dickinson <dfdpublic@wildtechgarden.ca>
[improved commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove a stray '|' character from 01_leds which has accidentally
been added.
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than GPIO LEDs, PHY LEDs do have an address.
Fix node names such that all gpio-leds do *not* contain an '@' sign and
PHY leds which do have an address also do contain the '@' sign.
This is done to prevent more copy&paste'ry of non-complaint DT
fragments.
Fixes: 7cbe34170e ("mediatek: add support for the GL.iNet GL-MT3000")
Fixes: fe10f97439 ("filogic: add support for GL.iNet GL-MT6000")
Fixes: e8f7597317 ("mediatek: filogic: add support for Cudy RE3000 v1")
Fixes: c9cb6411c1 ("mediatek: add support for Cudy WR3000 v1")
Fixes: 7560af7647 ("mediatek: filogic: migrate ASUS TUF AX6000 to upstream PHY LED control")
Fixes: 25ea7ff393 ("mediatek: filogic: migrate Acer W6/W6d to upstream PHY LED control")
Fixes: d50d51d74e ("mediatek: filogic: migrate Zyxel NWA50AX Pro to upstream PHY LED control")
Fixes: b88de5d507 ("mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control")
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Fixes: fd76a38190 ("mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
