Currently, both envtools and the rest of U-Boot tools are being built
regardless if the dumpimage package has been selected.
This will fail if only envtools are selected since the rest of tools
require OpenSSL while envtools do not require them.
So, only build tools if dumpimage is selected.
Fixes: 46e376c93514 ("uboot-tools: migrate uboot-envtools to uboot-tools")
Fixes: #18327
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/18329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make cpufreq work on different IPQ60xx SoC.
Also rebase ipq6018-cp-cpu.dtsi for mp5496.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh device tree, remove the useless sdhc2 aliases.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the minimal change for the upcoming patches.
Refresh the device tree of ipq807x at the same time.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because of the dt-bindings error, these patches have not
been merged yet, and the driver part is fine.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be used by GL.iNet devices from other target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Do not verify the format of TLV. Leave that to lldpd.
These lldpd config entries:
config custom-tlv
list ports 'eth0'
option tlv 'replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55'
config custom-tlv
option tlv 'oui 33,44,44 subtype 232'
list ports 'br-lan'
list ports 'eth0'
config custom-tlv # oui-info truncated
option tlv 'add oui 33,44,33 subtype 66 oui-info 5555555555'
config custom-tlv
option tlv 'add oui 33,44,31 subtype 44'
config custom-tlv # invalid oui
option tlv 'add oui 3322 subtype 79'
config custom-tlv # invalid oui
option tlv 'oui 3312 subtype 74'
Produce the following lldpd.conf content:
configure ports eth0 lldp custom-tlv replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55
configure ports br-lan,eth0 lldp custom-tlv oui 33,44,44 subtype 232
configure lldp custom-tlv add oui 33,44,33 subtype 66 oui-info 5555555555
configure lldp custom-tlv add oui 33,44,31 subtype 44
configure lldp custom-tlv add oui 3322 subtype 79
configure lldp custom-tlv oui 3312 subtype 74
And lldpd (v1.0.13 on v22) logs the following:
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op replace oui 33:44:55 subtype fe
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:44 subtype e8
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3322'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3312'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: lldpd should resume operations
( The last two TLV are invalid: their oui must be three hex bytes, comma
separated. Only the first hex byte of oui-info 5555555555 is used )
Depends on #14867 and its release version bump
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>
where csv = comma separated value(s)
Make the function more generic. Can use it for not only 'config'.
Now it can be used to parse interfaces for additional lldpd settings,
e.g. custom-tlv.
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add uboot-tools stub package skeleton which will replace uboot-envtools
and also provide target-builds for other U-Boot tools.
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
As described in #13873, from 23.05.0 onwards logging to a file on an
external filesystem fails under some conditions.
This occurs because the log initscript had code added to prevent start
logging to an external filesystem on boot, and added a trigger to start
said logging when the external filesystem gets mounted.
The issue is that for filesystems mount with fstab uci, the fstab
scripts runs at START=11, while log runs at START=12, which means the
external filesystem may already be mounted by the time the log initscript
runs. Since the external filesystem is already mounted it does not
trigger a hotplug event to trigger the trigger to start logging. This
combination means the logging never automatically starts when the log
file is on an external filesystem.
We therefore add a check for the presence of a mounted filesystem when
the log file is being sent to an fstab mounted filesystem. If the
filesystem is mounted, we don't skip starting logging during boot.
If the filesystem is not mounted then file logging is not started and
the trigger will start the logging when the filesystem is mounted.
Signed-off-by: Daniel F. Dickinson <dfdpublic@wildtechgarden.ca>
[improved commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove a stray '|' character from 01_leds which has accidentally
been added.
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than GPIO LEDs, PHY LEDs do have an address.
Fix node names such that all gpio-leds do *not* contain an '@' sign and
PHY leds which do have an address also do contain the '@' sign.
This is done to prevent more copy&paste'ry of non-complaint DT
fragments.
Fixes: 7cbe34170e ("mediatek: add support for the GL.iNet GL-MT3000")
Fixes: fe10f97439 ("filogic: add support for GL.iNet GL-MT6000")
Fixes: e8f7597317 ("mediatek: filogic: add support for Cudy RE3000 v1")
Fixes: c9cb6411c1 ("mediatek: add support for Cudy WR3000 v1")
Fixes: 7560af7647 ("mediatek: filogic: migrate ASUS TUF AX6000 to upstream PHY LED control")
Fixes: 25ea7ff393 ("mediatek: filogic: migrate Acer W6/W6d to upstream PHY LED control")
Fixes: d50d51d74e ("mediatek: filogic: migrate Zyxel NWA50AX Pro to upstream PHY LED control")
Fixes: b88de5d507 ("mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control")
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Fixes: fd76a38190 ("mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
PKG_MIRROR_HASH is incorrect and the package check is currently failing.
Fixes: 4990ce613b7d ("ipq-wifi: update to 2024-02-17")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
According to the MT7620A hardware datasheet, GPIO/14 was originally used for RIN of UARTF, but is now used as the WPS LED.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link TL-WR1043ND family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link Archer C7 v1/2/3 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link TL-WDR4300 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ar8216 switch driver supports exposing configuration of AR8327 and
AR8337 switch LEDs to the userspace, however it is only configurable
through platform data, causing the devices ported from ar71xx target to
lack the support.
Since there is still a long way to go until we can migrate the target to
qca8k, an interim solution is needed.
Extend ar8327_hw_config_of function to parse a "leds"
subnode, which will populate the missing platform data based on device
tree contents, and restore the existing support for the LEDs.
Standard bindings apply, mapping "reg" property to LED index, with
addition of "qca,led-mode" property, which selects HW (0) or SW (1)
mode, defaulting to HW mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch LEDs configured as active-low remain low instead of high upon
initialization, because in ar8327_leds_init, no distinction is made with
regards to LED pattern based on active_low property - only whether HW
mode is active. Select the proper initial pattern based also on
active_low to fix that.
While at that, simplify the equation ruling pattern selection for
setting brightness, avoiding unnecessary binary XOR operation, not
really valid for 'bool' type.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
