Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath10k dt-binding property "qcom,coexist-support" was
explicitly defined as type uint8 since upstream commit
ed09c61eb19d ("dt-bindings: net: Convert ath10k to YAML").
Therefore, this hack patch no longer makes sense.
Link: ed09c61eb1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.
A similiar change has been previously applied for RTL83xx in commit
cd958d945be0 ("realtek: 6.6: refactor mac config and link up for
RTL83xx").
Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 1375a7bae0d5e8dddb6b6cfe0584a399cd6c20b4.
This version does not activate the CONFIG_LEDS_CLASS_MULTICOLOR option,
this option is controlled by the generic target configuration.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The generic target configuration activates the
CONFIG_LEDS_CLASS_MULTICOLOR option. Do not deactivate it for the stm32
target.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This restores sysupgrade support
Since OpenWrt 23.05, the firmware selector no longer provides sysupgrade
images for RE450 V1 & V2 and RE355 v1 due to image size constraints
(~5.7MB limit), making the generic build unusable.
This commit moves RE450 V1 & V2 to the tiny target, enabling:
- Smaller image builds within the flash size limit.
- Restored sysupgrade support via the firmware selector.
- A secure-by-default wireless setup while allowing full management via UCI.
- Officially supported images, reducing the need for custom (potentially insecure) builds.
This ensures users can install a functional OpenWrt build without compromising security defaults.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
[Squashed the commits together and just copied the target definition
from the generic subtarget.]
Link: https://github.com/openwrt/openwrt/pull/18126
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.
When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Although ath10k pre-calibration data and board description file
have similar data structures, they are completely different things.
Therefore, let's remove these incorrect and confusing links.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18069
Signed-off-by: Robert Marko <robimarko@gmail.com>
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358d5 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79ccf ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
This new version fixes some memory leak and NULL pointer issues.
Upstreamed patches:
[1] 010-api_update.patch
[2] 201-wifi-ath10k-add-LED-and-GPIO-controlling-support-for.patch
The new 003 patch was introduced to fix the build error on old LTS
kernel. The patch 004 was used to fix the issue of IPQ4019 radio
not being able to start.
Tested on QCA9882 and IPQ4019.
[1] bca8bc0399
[2] 8e1debd824
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18368
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 7aa3dfdbda829c04475cffbd6708f1ff96e4849b.
As the kernel is now fixed with ecd609f509
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18380
Signed-off-by: Robert Marko <robimarko@gmail.com>
Only force compat_version to 1.2 if it was less than 1.2 before, as changes
1.1 and 1.2 were bootloader-related and a completed boot indicates that the
changes have been completed. Newer compat version 1.3 indicates a config change
and should not be forced on boot.
Fixes: 84fc59c0d5 ("mediatek: filogic: bpi-r3: set netdev-name for sfp1 port")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove settings and depends that are not used anywhere.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b6e5157527d3 fw4: fix reading kernel version
42d3b3d4ca21 fw4: allow family any for ipsets not matching IP addresses
edfdfc6df484 Revert "fw4: allow family any for ipsets not matching IP addresses"
97962771aa3c config: drop to-be-forwarded-nowhere packets on wans
00fc6943a297 init: remove unnecessary stop logic
ad3cba79c192 fw4: allow family any for ipsets not matching IP addresses
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[fix PKG_MIRROR_HASH]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18283
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patches 751-03 and 751-04 as a result of commit 6407ef8d2bcb4a0a6284de09cd77bd1868c1d6ea
were incorrectly placed in the backport folder.
So they return to their proper place.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.
Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.
Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.
Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add 'ubootmod' variant for the ASUS ZenWiFi BT8.
An out-of-tree installer will be provided in Github to allow users an easy
transition from the stock loader to OpenWrt's bootchain which is built from
source.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot build for the ASUS ZenWiFi BT8 intended to replace the
stock loader.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than most boards with DDR4 the ASUS ZenWiFi BT8 cannot use the
"comb" DDR calibration option and needs only the "ddr4" option set
instead.
Build TF-A SPIM-NAND with UBI as well as to boot from RAM with
mtk_uartboot for MT7988 with DDR4 RAM.
Signed-off-by: John Crispin <john@phrozen.org>
Break out all flash-layout dependent parts from device tree into separate
dtsi file to be used by both, stock layout and upcoming ubootmod variant.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7988D SoC (3x Cortex-A73 @1.8 GHz max)
1GB DDR4 RAM
128MB SPI-NAND (Winbond)
MediaTek MT7996 BE14000 Tri-Band Wi-Fi 7
3x LAN (2x 1GE MT7988 built-in, 1x 2.5GE MaxLinear GPY211C)
1x WAN (2.5GE MT7988 built-in)
LED: RGB PWM (supported as 3x PWM LED)
USB: 1x USB 3
Buttons: RESET, WPS
UART: 115200 8N1 3.3V
Installation
------------
1. Hold down RESET button and power on the device until
LED pulses red.
2. Assign IP 192.168.1.70/24 to your computer's Ethernet port
3. Connect Ethernet to one of the 1GE LAN ports
4. Open browser and visit http://192.168.1.1
5. Upload openwrt-mediatek-filogic-asus_zenwifi-bt8-factory.bin
6. Once OpenWrt initramfs system comes up, do sysupgrade using
openwrt-mediatek-filogic-asus_zenwifi-bt8-squashfs-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 21cece29e9eebc397eadee259e60c7fc44828cce.
Unfortunately, LibreSSL 4.0 causes the host APK tools to segfault under
fakeroot when .apk is being generated and it is completely breaking
building under Debian and Ubuntu hosts.
So, until this is fixed lets revert the update.
Signed-off-by: Robert Marko <robimarko@gmail.com>
In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Stable version. Odd versions are betas.
Added static patch to rename some ecdsa symbols that conflict with
u-boot's mkimage.
These symbols are not exported by default but because OpenWrt uses a
static libressl, they are present and conflict with mkimage's libecdsa.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16901
Signed-off-by: Nick Hainke <vincent@systemli.org>
